Hola hive blogueros espero estén bien un gusto compartir nuevamente con ustedes,en esta ocasión vengo a mostrarles como entorchar una cuarzo para usarlo como dije en un collar.
Hello hive bloggers I hope you are well pleased to share with you again, this time I come to show you how to twist a quartz to use it as I said on a necklace..
Para ello necesitaremos:
- Alambre de bisutería de 24ga (calibre).
- Pinzas,puede ser punta caimán o punta redonda.
- Un cuarzo de tu preferencia .
- Un collar de tu preferencia, se de cuero, cadena o yute.
For this we will need:
- 24ga (gauge) jewelry wire.
- Tweezers, can be alligator tip or round tip.
- A quartz of your choice.
- A necklace of your choice, be made of leather, chain or jute.
En lo personal prefiero entorchar las piedras preciosas con alambre de plata o cobre ya que de esta forma el cuarzo mantiene su poder de protección, mientras que el oro interfiere y le baja un poco su poder.
Personally, I prefer to twine precious stones with silver or copper wire since in this way the quartz maintains its protective power, while the gold interferes and lowers its power a little.
Proceso del entorchado:
- Cortamos 70cm del alambre de bisutería, en mi caso use Goldfield 24ga.
- Luego de los 70 cm medimos 10cm,alli hacemos un ojal del tamaño que sea acorde al collar donde lo queremos colocar.
- Ya hecho el ojal tomando el extremo más largo de alambre, procedemos a hacer curvas de arriba hacia abajo, la cantidad de curvas varia dependiendo del tamaño de la piedra que se va a entorchar, en mi caso bastaron cinco curvas.
- Ya listas las curvas, vamos a unir el final de la última curva con el alambre sobrante que quedo en el ojal,esto nos dará una forma de flor.
- En el centro de la flor colocaremos nuestra piedra, y vamos a ir cerrando cada pétalo como si abrazara nuestra piedra.
- Con la punta más larga que haya del alambre restante, uniremos las puntas de nuestros pétalos, haremos lo mismo por la parte posterior.
- Ya unidos los petalos, tomamos el otro extremo de alambre que queda del ojal y lo enrollamos en forma de espiral para darle un acabado a la pieza.
winding process:
- We cut 70cm of the jewelry wire, in my case I used Goldfield 24ga.
- After 70 cm we measure 10 cm, there we make a buttonhole of the size that is according to the necklace where we want to place it.
- Once the buttonhole has been made, taking the longest end of wire, we proceed to make curves from top to bottom, the number of curves varies depending on the size of the stone to be twisted, in my case five curves were enough.
- Now the curves are ready, we are going to join the end of the last curve with the excess wire that remains in the buttonhole, this will give us a flower shape.
- In the center of the flower we will place our stone, and we will close each petal as if it were hugging our stone.
- With the longest tip of the remaining wire, we will join the tips of our petals, we will do the same for the back.
- Once the petals are attached, we take the other end of the wire that remains from the eyelet and we roll it in a spiral shape to give the piece a finish.
Y listo para colocarlo en el collar de nuestra preferencia, a lucirlo se ha dicho.
And ready to put it on the necklace of our preference, to wear it has been said.
"Eres un ser de luz y magia, tienes el poder de atraer todo lo que deseas"
"You are a being of light and magic, you have the power to attract everything you want"
Todas las imágenes fueron tomadas desde un dispositivo Android