Here are the instructions on how i have made my chemtrail buster today
Above i have some quartz from the beach (usually opaq white) or if not near a beach dig it up, its probably in your garden as well.
4 - 6 copper pipes or any other metal pipes about 3 foot or bigger if possible. You can use smaller or less pipes and these still work well. The bigger and longer the pipes are the better.
Iron pyrite (the metallic looking rocks)
Cellanite the long piece
Black obsidian (the piece that looks like black glass)
Quartz chips (the lady at the shop gave me the crumbs for free)
Scouring pads
Anion curls (copper wire wrapped clockwise round a pen then snipped off about 4 cms)
Crushed glass (not too crushed little chunks)
diatomacious earth i use for the chickens but is good for the ion conversion
I also added some neodynium magnets but you can throw a few ordinary magnets if you wish, helps with the magnetic fields.
insulation tape
copper slug tape
a length of copper wire
The tiny little black ones are magnatite the same stuff found in bees.
The big black rock im afraid i have no idea but i picked it off the beach and it is some form of crystal, i use a loup to check. There are lots of different crystals you can use, however i was lucky to get my hands on these ones and i know they can work well. Shungite is expensive but works really well and activated charcoal as well. If you can't get all of these crystals just stick with quartz or amythyst, rose quartz it will still work. I have used a variety of crystals because they were available and they all help with different qualities and frequencies, so don't feel you need them all.
There are 4 terminated crystals and i have wrapped a tesla coil round it in a clockwise manner and made a spiral at the bottom of the one shown. I leave about 5cm at the top and cut the wire to a steep 70 degree cut so it is really sharp and pointy.
The other ingredients that i used is cement (no sand) but you can also use craft resin or car resin (bondo) so long as it catalyses. The heat and contraction of the resin or cement squeezing the crystals activates their pizzo electric ability which is why it needs to be set.
Take your favourite hammer to those pretty rocks and smash them up, you should end up with some small chunks and some really smashed stuff and it should look similar to this, and put it to one side while you deal with the terminated crystals.
Take the terminated crystals (long ones with a point with the tesla coil round it) and I have attached a copper cable to the coil which is to earth it in water or using a grounding rod in the soil; then i wrap the crystal and coil with insulating tape and place it in one end of the pipe and i have sealed the bottom with some copper slug tape and i have left the wire hanging out. I have only used one earthing cable, but place the remaining terminated crystals in the other pipes, also insulated and sealed with copper tape (slug tape).
The pipes can be copper, but i have cut up the rest of my childrens trampoline for the steel pipes. It is best to have about 3 foot and over i think for a better effect. Also try and use between 4 and 6 pipes as this helps with the amount it produces.
Now make a bucket of cement (just add water no sand) or if you are using resin make up the desired amount for your mould or bucket. Add all your stones and scouring pads, and your anion curls and mix it up to a fairly manageable mix, so you can get it into your mould or bucket. I added my diatomacious earth at this point.
Be sure to leave your earth cable hanging over the side of the bucket as you will want to put that in water or soil to plug in to the earth.
Simply push the pipes into the cement and spaced evenly around the mould with the sealed end of the pipes set into the cement or resin. Then this part gets a little tricky as you have to keep the poles upright while it dries. On this occasion i haven't done any fancy wooden brace with the holes cut out, i just shored it up with bits of wood until it dries which is why it looks untidy for now
Leave for a few days to set and then take it out of the mould or bucket and set it down in the garden or balcony, take the wire that is left out and put it in running water is best, or into a pond or hammer a steel rod into the ground and attach the end of your earth cable to it, then watch it work.
You should see the chemtrails stop dead like this picture..it was a heavy spray day so i added additional crystals to my chembuster to increase the effect, Love it.
If you want to make tower busters for your community then do the same mix and put in a smaller mould, muffin size and add a couple of cheap quartz chips in there and some scouring pads and let them set, they look like this.
Phew.....last of all please let me know if you are unsure of anything and i will try to help, there was a lot of typing in this article and i hope i didn't forget anything.
Take some pictures of what you have done with your cloudbuster and put #mycloudbusterdidthis
Thanks and please upvote if this was helpful and comments or feedback are always welcome.
