---

Happy and blessed day, I think it is the first time that I publish this great community, I really appreciate that your contest is open to all, since in this way I have the honor to participate .. I love to create and innovate more than my work is my passion and you giving me an open letter to create was wonderful uffs. I have made you a tutorial of a Christmas Hat made at home step by step I hope you like it, Christmas is a time to help and give back all that we have by being grateful.

---

---

I have made a Christmas hat with frosted foam, it is quite elaborate, I tried to explain it in the most detailed way possible, my intention was to make a top hat inspired by the hat of the Hatter from the movie Alice in Wonderland, it is the first time I have made one, between mistakes I learned a lot and I really enjoyed the process, I explain it step by step with a sequence of images. Dare to learn with me !! We start:

---

Step 1: as you will see the images we must make the patterns in each image is the pattern with its measurements then cut it out and transfer it from the back to the foami with a pencil, then carefully you cut out all the foami to create the piece.

Step 2: When we finish cutting the pieces in the foami, you can pass a height stick around the edge, then in one of the large circles make a smaller circle in the center in part 1 are the patterns and the measurement must be cut in the center in four.

Step 3: We are going to line the base for the headband with hot silicone and foam, to begin with, start placing a line of hot silicone on the base for the headband and glue the foam no matter if the foami is bigger because later with the scissors you can cut it to the size of the headband now we are going to put this aside so that it dries well and we continue our hat

Step 4: with the help of the silicone gun we are going to glue the central part as you will see, we will leave a tab on it, put hot silicone on it and stick the other end on it, now on The circle that we opened the center in El Paso above, we are going to place hot silicone around it and it will be glued to the center of the piece, you can help with the sequence of images!

Step 5: very carefully pass the flame of the lighter along the entire edge of the piece so that it can be lowered and smooth. Now put a little hot silicone on the edge and on each tab and paste the small circle.

Step 6: Make on a sheet a pattern like dripping snow, cut it and transfer it to the foam, then cut it again and with the help of the glue gun, stick it on the upper edge of the hat . It will look beautiful 🤩

Step 7: With patience we are going to make a buckle with gold and black, well I used brown because there was no black 🤦🤷 make two squares of 6 centimeters in diameter each, paste one on another one on top of the gold and then we will stick it on the hat right in the center.

Step 8: We are going to make the decorations, cut strips of foami 1 centimeter wide in two colors or whatever you like best, start rolling over them AND placing a little hot silicone Be careful not to burn yourself if you put too much it will come out from the sides. When finished, cut the rest, make as many as you like.

Step 9: It's time to make the loop, cut 2 strips 18 centimeters long by 4 centimeters wide each with the help of the lighter burn the ends of the ribbon, now fold it at the half and pass the lighter carefully to mark the center, fold each point inwards and sew through the center with a straight seam, carry out this step on the other strip and sew with the same thread, when finished pull the thread to make pressure then tie and cut the remaining thread.

Step 10: In this step you can start gluing the decorations, to your liking you don't need it to be the same, be creative and dare to innovate! 🤗😊

Step 11: Make the pattern of a snowflake on a sheet, cut it and transfer it to the foami. If you are good at drawing, you just have to draw it on the foami and cut, when finished, put hot silicone on it and stick it on one edge of our beautiful Christmas hat. Now we are going to fix it on the headband, measure where it will be placed, spread a little hot silicone and stick the Christmas hat, now stick the large circle that we have left underneath, in this way we cover the Headband and the hole.

Step 12: This step is optional, when I finished the hat I noticed that the bottom part had been very small and did not resemble the idea that was in my mind, so I added An extra piece to make it bigger and thus take life, in the sequence of images you have the measurement if you want to do it, when making the pattern and cutting in the foami cut the foami on one side so that we can insert it into the hat we must glue it with hot silicone carefully, reattach the decorations and in this way we finish our beautiful Christmas hat! Thanks for reading ... 🤗😊💋😄

Autoría del texto y todas las imágenes: @Marleyn , La edición de las imágenes las realicé yo misma, Por favor no Utilices mis fotos sin mi autorización, edites ni re-publiques mi material ¿Deseas ponerte en contacto conmigo? Escríbeme:
Correo electronico: Marleynl123@gmail.con
Discord Marleyn#7821
Twitter: Hive account@marleynleal1
Imstagran: @MarleynSoutache

Authorship of the text and all the images: @Marleyn, Editing of the images was done by myself, >Please do not use my photos without my authorization, edit or re-publish my material Do you want to >contact me? Write me:
Email: Marleynl123@gmail.con
Discord Marleyn #7821
Twitter: Hive account@marleynleal1

Imstagran: @MarleynSoutache

Mi trabajo es mi pasión y cuando tu trabajo es tu pasión nada es imposible / My work is my passion and when your work is your passion nothing is impossible