Hello friends from Hive and the Build-it community. Today I want to present my latest work, it is a Chopper style motorcycle made with computer parts, specifically with parts of the hard disk. This project took me a full week to do. I had some inconveniences because I had never worked with this material and I did not use any pattern or model other than photos of real Chopper motorcycles to get an idea. All parts only include hard drive parts and to assemble it I used small screws. I hope you like my work.
Hola amigos de Hive y de la comunidad Build-it. Hoy quiero presentarles mi ultimo trabajo, se trata de una motocicleta estilo Chopper hecha con partes de ordenador, especificamente con partes del disco duro. Este proyecto me tomó hacerlo una semana completa. Tuve algunos inconvenientes porque nunca habia trabajado con este material y no usé ningun patron o modelo mas que fotos de motocicletas Chopper reales para tener una idea. Todas las partes solo incluyen piezas de disco duro y para armarlo usé tornillos pequeños. Espero que les guste mi trabajo.
Process
For this project I used 12 burned hard drives without any functioning, the parts it brings are the record, the reading stylus, the magnets to hold the stylus and the motor that makes the record spin. The disc is used for the wheels, the motors to make the axle and bearings, the needles to make the gears, and the magnets for the seat and fork. I also used part of the board with the electronic circuits.
Para este proyecto utilicé 12 discos duros quemados sin nada de funcionamiento, las piezas que trae son el disco, la aguja lectora, los imanes para sostener la aguja y el motor que hace girar el disco. El disco es usado para las ruedas, los motores para hacer el eje y los rodamientos, las aguja para hacer engranajes y los imanes para el asiento y la horquilla. Tambien usé parte de la placa con los circuitos electronicos.
First we start making the fork for the front wheel, we take a pair of magnets and observe where they have holes. Then we take two rods and place them inside the holes, for the rods I used some antennas from some old televisions and cut them to size so that it would look good.
Primero comenzamos haciendo la horquilla para la rueda delantedra, tomamos un par de imanes y observamos por donde tienen unos huecos. Luego tomamos dos varillas y se las colocamos dentro de los huecos, para las varillas yo usé unas antenas de unos televisores viejos y las corté a la medida para que quedará bien.
The next step is to make the wheels, for them we take the discs and put several of them in a motor. It is important to use several so that the wheels have a good thickness, remember that these motorcycles are characterized by having wide wheels and tires. We make two wheels.
El siguiente paso es hacer las ruedas, para ellos tomamos los discos y colocamos varios de ellos en un motor. Es importante usar varios para que las ruedas tengan un buen grosor, recordemos que estas motocicletas se caracterizan por tener ruedas y neumaticos anchos. Hacemos dos ruedas.
Then we started to build the frame of the bike. The first part is to locate the gas tank, for this we use a mouse that no longer works and we put it as a gas tank. To make the base that goes from the fork to the frame of the motorcycle we use the reading needles. We can glue them with silicone to use screws, I used both options to achieve consistency since these pieces have a certain weight and the frame could give way.
Despues comenzamos a cosntruir el cuadro de la moto. La primera parte es ubicar el tanque de la gasolina, para esto utilizamos un raton que ya no sirva y lo ponemos como tanque de gasolina. Para hacer la base que va de la horquilla al cuadro de la motocicleta usamos las agujas lectoras. Podemos pegarlas con silicon a usar tornillos, yo usé ambas opciones para asi lograr consistencia ya que estas piezas tienen cierto peso y el cuadro podría ceder.
We will make the frame on the inside with pieces of the plate, we cut it to the size we need and using the holes that it brings by default through them we put screws with screws and screw them. We fix the parts well and we also make a hole in the small front rod. When we put these parts together, the painting remains this way.
El cuadro en la parte interna lo haremos con trozos de la placa, la cortamos a la medida que necesitamos y usando los agujeros que ella trae por defecto a traves de ellos ponemos tornillos con tuerzas y enrroscamos. Fijamos bien las partes y tambien le hacemos un agujero a la pequeña varilla delantera. Cuando unimos estas partes el cuadro nos va quedando de esta manera.
Once we have finished with the frame we proceed to build the part of the rear wheel. We take two needles and fix them with screws to the center of the shafts and both needles at the other ends we fix them with a small metal plate. We must measure it so that it is the thickness of the frame and tailored to the gas tank. We make a couple of holes in the sides and screw the needles that will be the arms that hold the rear wheel.
Una vez hemos finalizado con el cuadro procedemos a construir la parte de la rueda trasera. Tomamos dos agujas y las fijamos con tornillos al centro de los ejes y ambas agujas en los otros extremos las fijamos con una pequeña placa de metal. Debemos medirla para que nos quede del grosor del cuadro y a medida del tanque de gasolina. Le hacemos par de agujeros a los lados y fijamos con tornillos las agujas que serán los brazos que sostienen la rueda trasera.
The next step is to attach the frame to the rear wheel. We used two rods to join from the frame to the metal plate that holds the rear wheels. At both ends we fix them tightly using screws and tightening the nuts very well so that the motorcycle is not loose.
El siguiente paso es unir el cuadro a la rueda trasera. Usamos dos varillas para unir desde el cuadro hasta la placa de metal que sostiene las ruedas traseras. En ambos extremos los fijamos fuertemente usando tornillos y apretando muy bien las tuercas para que la motocicleta no quede floja.
We use the plate that is inside the mouse and we put it on the bottom of the motorcycle, we do this so that that part is not discovered and thus has a more technological and steampunk aesthetic. As you can see, the body of the motorcycle is 60% complete, only missing the fork and making small details. This is when we can see that we are on the right track when we are doing a job.
Usamos la placa que esta dentro del raton y la ponemos en la parte inferior de la moto, esto lo hacemos para que no nos quede descubierta esa parte y asi tenga una estetica mas tecnologica y steampunk. Como pueden observar el cuerpo de la motocicleta esta completo en un 60% solo le falta la horquilla y hacer pequeños detalles. Aqui es cuando podemos ver que vamos en buen camino cuando estamos haciendo un trabajo.
Then we adjust the fork that we made in the beginning to this hole with a screw. We can press hard and it will be fixed or we can also leave it a little soft so that the fork has movement .. The cat did not let me work so it also appeared in the photo, it helped me to test the fit of all the pieces lol. For the seat, if you look closely, place magnets at both ends. As they also have holes I fixed them in the frame with screws and they were very well located.
Luego Ajustamos la horquilla que hicimos en el principio a este agujero con un tornillo. Podemos apretar fuertemente y nos quedará fija o tambien podemos dejarla un poco suave para que la horquilla tenga movimiento.. La gata no me dejaba trabajar asi que salió tambien en la foto, me sirvio para probar el ajuste de todas las piezas jejeje. Para el asiento si observan bien coloque imanes en ambos extremos. Como tambien poseen agujeros los fijé en el cuadro con tornillos y quedaron muy bien ubicados.
To finish I added the steering wheel for which I used the protector that bicycles have on the brakes where the cable that pulls the brakes goes. Cut two pieces and pose them at both ends. For the headlight use one of the motor shafts. I also made a small modification in the part where the fork is attached to the rest of the frame since I realized that it looked a bit far from each other and that did not give a good aspect of proportion so I decided to cut it a little to make it fit best.
Para finalizar agregué el volante para el cual usé el protector que tienen las bicicletas en los frenos por donde va el cable que tira de los frenos. Corte dos trozos y los pose en ambos extremos. Para la luz delantera use uno de los ejes de motor. Tambien hice una pequeña modificacion en la parte donde va fijada la horquilla al resto del cuadro ya que me di cuenta de que se veia un poco alejado uno de otro y eso no daba un buen aspecto de proporcion asi que decidi recortarlo un poco para que quedara mejor.
Final Work
And this is how the bike made with computer hard drive parts turned out. The work took me exactly as I had told you for a week and it is the first I did with these materials. The rest of the pieces that I did not use, I am already thinking about how to put them to good use in a new job soon. I hope you like it and if you like it, leave a comment and support my work, if you like, you can follow me and so you will not lose my future works and you can see my previous works. My commitment is to show how easy it is to work recycling and that we can create new things by letting our imaginations fly. Also make the Hive community grow into better content since it is the only one that truly supports art. So please support all the artists who do great work. I say goodbye to you, wishing you a good weekend.
Y asi es como me ha quedado la moto hecha con piezas de disco duro de ordenadors. El trabajo me llevo como les habia comentado una semana extactamente y es el primero que realizo con estos materiales. El resto de piezas que no utilicé ya estoy pensando en como darles un buen uso porximamente en un nuevo trabajo. Espero les guste y si les gusta dejen un comentario y apoyen mi trabajo, si gustan pueden seguirme y asi no se perderan mis futuros trabajos y pueden ver mis obras anteriores. Mi compromiso es hacer ver lo facil que es trabajar el reciclaje y que podemos crear cosas nuevas dejando volar nuestra imaginacion. Tambien hacer que la comunidad de Hive crezca en mejor contenido ya que es la unica que verdaderamente apoya el arte. Por eso apoyen a todos los artistas que hacen un gran trabajo. Me despido de ustedes deseandoles un buen fin de semana.
I'm also on instagram if you want to follow me.
Tambien estoy en instagram por si desean seguirme.