Hermosa lampara echa con alambre de cobre y vidrio reciclado
Beautiful lamp made with copper wire and recycled glass
Saludo amigos espero se encuentren bien, el día de hoy quiero compartir con ustedes una hermosa lampara echa con alambre de cobre y unos vidrios resiclados los vidrios los conseguí con mi madre ella iba a desechar una lámpara vieja ya estaba un poco deteriorada ya sin arreglo pero los vidrios estaban muy bien por eso decidí hacer una lámpara con alambre y darle una nueva vida a esos vidrios espero les guste.😉☺️🌹🌹
Greetings friends I hope you are well, today I want to share with you a beautiful lamp made with copper wire and some recycled glass I got the glass from my mother she went to throw away an old lamp it was already a little deteriorated no repair but the glasses were very good so I decided to make a lamp with wire and give a new life to those glasses I hope you like it.
Que necesitamos .
What do we need.
vidrios resiclados
tenazas
alambre de cobre grueso y fino
- recycled glass
- pincers
- coarse and fine copper wire
comencemos con el paso a paso
let's start with the step by step
Paso 1: Cortaremos seis troso de alambre de cobre trataremos de cortarlos del mismo largo así nos quedaran parecidas después de cortar tomaremos nuestras pinzas y doblaremos las dos puntas, cortaremos dos troso de alambre y doblaremos en seis parte aremos uno más grande que el otro Nos quedaran como un Exagonal despue entorcharemos un trozo de alambre en un lápiz y lo cortaremos quedaran unos redondos estos los utilizaremos para unir las dos puntas de los exagonales .
Step 1: We will cut six pieces of copper wire we will try to cut them of the same length so they will be similar after cutting we will take our pliers and bend the two ends, we will cut two pieces of wire and we will bend in six parts we will make one bigger than the other one We will have a Hexagonal, then we will twist a piece of wire in a pencil and we will cut it. We will use some round ones to join the two ends of the hexagonal.
Paso 2: tomaremos las primeras piezas que hicimos y la doblaremos un extremo hacia un lado después doblaremos lo redondo hacia arriba ya teniendo una especie de curva doblaremos lo más grande hacia arriba después lo enderezar emos este paso lo aremos en todas las puntas de todas las piezas nos quedaran como lo vemos en la foto y así ya teniendo estás piezas lista empezamos a unir nuestras piezas
Step 2: we will take the first pieces that we made and we will bend one end to one side, then we will bend the round part upwards, already having a kind of curve, we will bend the largest part upwards, then we will straighten it, this step we will do it in all the ends of all the pieces will remain as we see in the photo and thus having these pieces ready we begin to join our pieces.
Paso 3: En este paso aremos una especie de U y le aremos unas puntas hacia arriba después lo uniremos el la parte de abajo de nuestra lampara esta U nos ayudará a que no se nos caiga nuestro vidrio después cortaremos unos troso de alambre y aremos aspirales para darle un poco de vista a nuestra lampara esta también nos servirán para sujetar el vidrio porque a estos aspirales le daremos un poco largo la punta y el vidrio irá en el mío, recordemos apretar con las tenazas muy bien
Step 3: In this step we will make a kind of U and we will make some points upwards, then we will join it to the bottom of our lamp, this U will help us not to drop our glass, then we will cut some pieces of wire and we will make aspirales to give our lamp a bit of a view, this will also serve to hold the glass because we will give these aspirales a little long tip and the glass will go in mine, remember to press very well with the pliers.
Paso 4: para este paso cortaremos seis troso de alambre del mismo largo doblaremos las puntas, l daremos forma con nuestras manos después de tener las seis piezas lista la sujetamos muy bien con nuestro alambre delgado después de ordenar y sujetar muy bien le doblaremos las puntas para enganchar en nuestra lampara esta será la parte de arriba apretamos muy bien con las tenazas y listo.
Step 4: for this step we will cut six pieces of wire of the same length we will bend the ends, we will shape it with our hands after having the six pieces ready we will hold it very well with our thin wire after ordering and holding it very well We will bend the ends to hook on our lamp, this will be the upper part, we press very well with the pliers and that's it.
lista nuestro hermosa lampara, espero que a las damas les guste, fue un gusto compartir con ustedes .
list our beautiful lamp, I hope the ladies like it, it was a pleasure to share it with you.
Todas las Fotos son de mi autoría y fueron tomadas con mi Celular Redmi 9T
All Photos are my authorship and were taken with my Redmi 9T Cellphone