ESPAÑOL
Hola mis amigos, en este 2025 no había tenido oportunidad de hacer vida por acá por la comunidad, espero y deseo que todos gocen de buena salud y mucha paz en sus vidas y entorno familiar.
En estos últimos tiempos he estado inmerso en las reparaciones de televisores de pantalla plana de cristal líquido (LCD), y en muchas ocasiones la falla se debe al deterioro de los diodos LED de las tiras que conforman el Backlight, el cual se encarga de iluminar el panel LCD permitiendo que podamos ver las imágenes en nuestra TV.
Para sustituir cada LED dañado en una tira es necesario tener una plancha de calor para desoldar y soldar LED (existen otros métodos, pero considero que el uso de esta herramienta es lo más eficiente y cómodo que se puede hacer) las cuales venden en muchas tiendas online e incluso en los grupos de compra y ventas que existen en mi país; sin embargo, en estos momentos no cuento con el presupuesto para destinarlo a la compra de dicha herramienta por lo que decidí construirla aprovechando materiales 100 porciento reciclados de otros equipos en desuso.
ESPÓILER: Con esta herramienta totalmente DIY, podrás reparar los bombillos, focos y linternas LED que tengas dañados. También se podrá usar para desoldar y reciclar componentes electrónicos en algunas placas de circuito impreso.
CONSTRUCCIÓN DE LA PLANCHA DE CALOR.
El elemento principal de esta herramienta consiste en aprovechar la resistencia de calor que se encarga de mantener la temperatura en una olla arrocera después que termina de cocer el arroz. Puede ser que este tipo de resistencia varíe en dependencia del modelo de la olla, pero la que utilicé tiene una resistencia de 290 Ohms entre sus terminales, y se alimenta con 110 volts de corriente alterna.
MATERIALES.
- Reciclar la resistencia de mantenimiento de una olla arrocera.
- Para la base o soporte de la resistencia utilicé la caja metálica de un viejo protector de voltaje que estaba en desuso por mal funcionamiento.
- Para la conexión de la resistencia a la red eléctrica, utilicé un cable de alimentación reciclado de una olla en mal estado técnico, pero con el cable en óptimas condiciones.
- También fue necesario reciclar un terminal de conexión rápida, un trozo de aislante eléctrico y tornillos para fijar la resistencia al soporte.
PASO A PASO
- Después de reunir todos los materiales, lo siguiente fue realizar algunos orificios a la carcasa para poder fijar la resistencia y el terminal de conexión rápida.
- Lo siguiente fue acoplar la resistencia al soporte y hacer las conexiones entre los terminales de la resistencia y el cable de alimentación a través del terminal de conexión rápida, como se describe en las siguientes imágenes.
- Cómo último paso empalme los cables de alimentación y les puse aislante para evitar cortocircuitos.
Resultado Final
Probando la plancha.
Una vez terminada es necesario probar si cumple con la función esperada, para ello hice varias pruebas como se aprecia en las siguientes imágenes.
Desoldando los LED de una pequeña tira
LED retirados
Sustituyendo los diodos LED dañados de un bombillo
Tira encendida después de sustituir los diodos LED
Reciclando componentes electrónicos en una placa de circuito impreso
Debo decir que los resultados obtenidos fueron satisfactorios y cumplieron con mis expectativas, ya que la plancha alcanza la temperatura adecuada para fundir el estaño sin llegar a desarrollar una temperatura demasiado elevada que pueda dañar los componentes electrónicos.
Espero que esta plancha DIY me sirva para realizar mis reparaciones durante un buen tiempo hasta que pueda adquirir una más profesional, pero por ahora me siento satisfecho con los resultados.
Se emplearon materiales reciclados para su construcción y lograr el resultado final conlleva un bajo nivel de dificultad, por lo que si eres de las personas que les gusta fabricar sus propias herramientas espero que esta publicación te sirva de base para hacer algo similar, siempre tomando las medidas de protección necesarias para evitar accidentes.
Me despido deseándoles un buen día mis amigos, hasta la próxima.😉
Las fotos fueron tomadas con mi celular Xiaomi Redmi Note 6 pro y editadas en la app "Galería" del propio teléfono.
Imagen de portada creada en la a Canva
Puedes verme en Facebook
ENGLISH
Hello my friends, in this 2025 had not had the opportunity to make life here by the community, I hope and wish that all enjoy good health and peace in their lives and family environment.
In recent times I have been immersed in repairs of liquid crystal display flat panel televisions (LCD), and in many occasions the failure is due to the deterioration of the LED diodes of the strips that make up the Backlight, which is responsible for illuminating the LCD panel allowing us to see the images on our TV.
To replace each damaged LED in a strip is necessary to have a heat plate to desolder and solder LED (there are other methods, but I consider the use of this tool is the most efficient and convenient that can be done) which are sold in many online stores and even in the groups of purchase and sales that exist in my country; however, at this time I do not have the budget to allocate it to the purchase of such a tool so I decided to build it using materials 100 percent recycled from other equipment in disuse.
SPOILER: With this totally DIY tool, you can repair damaged light bulbs, spotlights and LED flashlights. It can also be used to desolder and recycle electronic components on some printed circuit boards.
CONSTRUCTION OF THE HOT PLATE.
The main element of this tool consists of taking advantage of the heat resistor that is in charge of maintaining the temperature in a rice cooker after the rice has finished cooking. This type of resistance may vary depending on the model of the pot, but the one I used has a resistance of 290 Ohms between its terminals, and it is fed with 110 volts of alternating current.
MATERIALS.
- Recycle the maintenance resistance of a rice cooker.
- For the base or support of the resistor I used the metal box of an old voltage protector that was in disuse due to malfunction.
- For the connection of the resistor to the mains, I used a power cable recycled from a pot in poor technical condition, but with the cable in good condition.
- It was also necessary to recycle a quick-connect terminal, a piece of electrical insulator and screws to attach the resistor to the bracket.
STEP BY STEP
- After gathering all the materials, the next thing to do was to drill some holes to the housing in order to attach the resistor and the quick connect terminal.
- Next was to attach the resistor to the bracket and make the connections between the resistor terminals and the power cable through the quick connect terminal, as described in the following pictures.
- As a last step, I spliced the power cables and insulated them to avoid short circuits.
Final Result
Testing the plancha.
Once finished it is necessary to test if it fulfills the expected function, for this I made several tests as shown in the following images.
Desoldering the LEDs of a small strip
LEDs removed
Replacing damaged LED diodes in a light bulb
Strip on after replacing LED diodes
Recycling electronic components on a printed circuit board
I must say that the results obtained were satisfactory and met my expectations, since the iron reaches the right temperature to melt the tin without developing too high a temperature that could damage the electronic components.
I hope that this DIY iron will serve me to make my repairs for a long time until I can acquire a more professional one, but for now I am satisfied with the results.
Recycled materials were used for its construction and achieving the final result involves a low level of difficulty, so if you are one of those people who like to make their own tools I hope this publication will serve as a basis for you to do something similar, always taking the necessary protective measures to avoid accidents.
I say goodbye wishing you a good day my friends, until next time.😉
The photos were taken with my Xiaomi Redmi Note 6 pro cell phone and edited in the “Gallery” app of the phone itself.
Text translated to English in Deepl translator.
Cover image created in Canva
You can see me at Facebook