Hello friends of Hive, I send a big greeting to all the users who make this community great with the work of their hands and their fabulous creations. Today I want to share with you, after many days without doing anything, my latest handwork with recycled material. I always wondered what the lovable R2-D2 would look like if it were a Dith Lord, and it turns out that there was an Imperial version of this droid that worked for the empire's forces. He made a cameo appearance in the Return of the Jedi movie and was to be featured in the Star Wars spin-off Rogue One, however we never saw him make any entries. It already exists in the collectible figures market so I decided to make one for myself, I hope you like it.
Hola amigos de Hive, envío un gran saludo a todos los usuarios que hacen grande esta comunidad con la obra de sus manos yu sus fabulosas creaciones. Hoy quiero compartir con ustedes luego de muchos días sin hacer nada mi último trabajo hecho a mano con material reciclado. Siempre me pregunataba como se vería el adorable R2-D2 si fuera un Lord Dith, y resulta que existió una versión imperial de este droide que trabajaba para las fuerzas del imperio. Hizo un cameo en la peícula El Retorno Del Jedi e iba a ser incliudo en el spin-off Rogue One de Star Wars, sin embargo nunca lo vimos hacer alguna entrada. Existe ya en el mercado de figuras de colección así que he decidio hacer uno para mi, espero que les guste.
Process
For this job the primary recycling material is the beer can, as I said before it has many ways to use it. To begin we remove the entire top.
Para este trabajo el material de reciclaje primordial es la lata de cerveza, como he dicho antes tiene muchas formas de usarse. Para comenzar retiramos toda la parte de arriba.
Then the second step is to make the limbs, which in total are three. We make the first two of a larger measure that go to the sides. We cut the can, we make the measurements according to our criteria and then we begin to bend where we have marked. Finally we glue with glue.
Luego el segundo paso es hacer las extremidades ue en total son tres. Hacemos las dos primeras de una medida mas grande que van a los lados. Cortamos la lata, hacemos las medidas segun nuestro criterio y luego comenzamos a doblar donde hayamos marcado. Por ultimo pegamos con pegamento.
The next step is to prepare the bases that help to fix the limbs to the rest of the robot. We make some templates considering the original model and choosing measurements that are exact, I did it with 3 cm, so I could work better. Then we cut the cans following the pattern that we drew and then we cut some 10mm thick strips that will serve us to join the templates that we have just cut.
El paso siguiente es preparar las bases que ayudan a fijar las extremidades al resto del robot. Hacemos unas plantillas considerando el modelo original y escogiendo medidas que sean exactas, yo lo hice con 3 cm, asi pude trabajar meor. Luego cortamos las latas siguiendo el patron que dibuamos y despues cortamos unas tiras de 10mm de grosor que nos serviran para juntar las plantillas que acabamos de cortar.
Having everything done and tracing is very simple, we take both parts and join them with the tape that we cut. Once each shoulder is finished then we glue the rectangles that we made before.
Teniendo todo hecho y trazado es muy sencillo, tomamos ambas partes y las unimos con la cinta que cortamos. Una vez terminado cada hombro entonces pegamos los rectángulos que hicimos antes.
Next we make the bases of the extremities, this one I made 30 mm long and 15 mm high. Then we make the end of the center that is the smallest and we glue it to the base.
Seguidamente hacemos las bases de las extremidades, esta las hice de 30 mm de largo y 15mm de alto. Luego hacemos la extremidad del centro que es la mas pequeña y la pegamos a la base.
Once we have joined each part of the limbs we begin to put them in the rest of the can. First we glue one of the extremities to the bottom of the can. Then on the sides with all screws with their nuts we fix the other two extremities. This is how it would be, it can be seen that it is 90% done.
Una vez que hayamos unido cada parte de las extremidades comenzamos a ponerlas en el resto de la lata. Primero pegamos en la parte inferior de la lata una de las extremidades. Luego en los lados con todos tornillos con sus tuercas fijamos las otras dos extremidades. Así es como nos quedaría, puede verse que ta esta hecho en un 90%.
Now we will move our friend to the Dark Side of the Force using black spray paint, we apply two layers of paint and this is how the droid R2-Q5 looks impressive.
Ahora pasaremos a nuestro amigo al Lado Oscuro de la Fuerza usando pintura negra en spray, aplicamos dos capas de pintura y así se ve de imponente el droide R2-Q5.
Finally, we put the accessories around the robot that it wears and that makes it look different. For this I used orange and silver colored cans.
Por ultimo colocamos alrededor d etodo el robot los accesorios que lleva y que lo hace lucir diferente. Para esto utilicé latas de color naranja y plateado.
Final Work
This is what this imposing R2-Q5 droid looks like, I've been making these figures for a long time so I can't hide my fanaticism for Star Wars, I really wanted to see it in the latest movies but it couldn't be. I hope you liked my contribution. Remember to always give freedom to the imagination, so we will always find useful materials to do great things. I say goodbye to all of you see you soon. May the force be with you.
Así es como se ve este imponente droide R2-Q5, desde hace mucho realizo estas figura asi que no puedo ocultar mi fanatismo por Star Wars, deseaba mucho poder verlo en las últimas películas pero no pudo ser. Espero que les haya gustado mi aporte. Recuerden siempre darle libertad a la imaginación, así siempre encontraremos materiales útiles para hacer grandes cosas. Me despido de todos ustedes hasta pronto. Que la fuerza los acompañe.