Hola que ta? Amigos de esta comunidad, es un gusto saludarles una vez más. Shalom. 🫂🫂. Esperando que se encuentren muy bien. Por acá le escribe Jerm20 y quiero compartir con ustedes el trabajo de preparación y pintado del tanque para mi moto, cariñosamente apodada "LA NIÑA" 🛵🛵🛵🛵🛵.
En uno de mis Posd compartí la experiencia de comprar el tanque y lo difícil que era conseguir el color Amarillo 😳😳, ahora quiero compartir la experiencia del pintado... 😁😁😁
Como siempre digo al comienzo de mis publicaciones: Primero lo primero...😊, con el tanque ya en mis manos, venía la magnífica tarea de pintarlo, buscar primero un amarillo que fuese Lindo y no muy intenso, y lo conseguí Gloria a Dios 👍👍, poco a poco fui comprando las cosas para hacer el trabajo, pintura, lija número 2000, tirro o adhesivo y por supuesto el Tinel para diluir o disolver la pintura.
Hi, how are you? Friends of this community, it is a pleasure to greet you once again. Shalom. 🫂🫂. Hoping you are doing very well. This way writes Jerm20 and I want to share with you the work of preparation and painting of the tank for my bike, affectionately nicknamed "THE GIRL" 🛵🛵🛵🛵🛵.
In one of my Posd I shared the experience of buying the tank and how difficult it was to get the yellow color 😳😳, now I want to share the experience of painting... 😁😁😁
As I always say at the beginning of my publications: First things first...😊, with the tank already in my hands, came the magnificent task of painting it, first look for a yellow that was Nice and not too intense, and I got it Glory to God 👍👍, little by little I was buying the things to do the job, paint, sandpaper number 2000, tirro or adhesive and of course the Tinel to dilute or dissolve the paint.
Lo primero que hice fue preparar el acabado, la superficie para poder pintar y obtener un resultado de primera 👍👍👍, como el tanque viene con sus tapas y trae sus Calco manías, para no dañarla tuve que empezar el minucioso Trabajo de cubrirlas tanto del tanque como de las tapas, Para esto se utiza el adhesivo blanco, el cual es especial para ese tipo de trabajo, cubrí cuidadosamente Cada calco manías y para tener un mejor acabado cortaba los bordes con una hojilla, así estuve trabajando como dos o tres días porque tenía otros compromisos 😁😁😁, hasta que por fin termine de tapar las Calco🤣🤣🤣. Luego venía el trabajo de preparar la superficie, para esto utilice una lija 2000, y le pase suavemente a las tapas y al tanque, lije y echándole agua, este proceso es para quitar el brillo de la pintura que trajo el tanque y las tapas y de esta manera agarra MUCHISIMO MEJOR LA NUEVA PINTURA. ALELUYA!!!!!
En las imágenes se puede apreciar el tanque y las tapas ya lijados, se puede notar que ya el color verde esta opacado👍👍, listo para pintar.
The first thing I did was prepare the finish, the surface to be able to paint and get a first class result 👍👍👍, as the tank comes with its covers and brings its Decal manias, in order not to damage it I had to start the meticulous work of covering both the tank and the covers, For this the white adhesive is used, which is special for that type of work, I carefully covered each decal manias and to have a better finish I cut the edges with a razor blade, so I was working for two or three days because I had other commitments 😁😁😁, until I finally finished covering the Decal🤣🤣🤣. Then came the work of preparing the surface, for this I used 2000 grit sandpaper and gently went over the covers and the tank, sanding and adding water, this process is to remove the shine of the paint that the tank and covers had and in this way the NEW PAINT adheres MUCH BETTER. HALLELUJAH!!!!!
In the images you can see the tank and lids already sanded, you can see that the green color is already opaque👍👍👍, ready for painting.
Entre los materiales utilizados se me pasó nombrar el transparente 🤣, terminado el proceso de acabado para pintar, espere un día que hiciera buen sol y así fue... Llego el gran dia 😁😁, a pintar. Se preparo la pintura con el Tinel, se encendió el compresor y a pintar, primero la parte inferior del tanque y luego la superior, simultáneamente se le colocó la primera mano al Guarda barro y a las tapas 👍👍👍, mientras secaba la primera mano en el tanque... Al secar se le dio la segunda mano, una vez seco se procedió a retirar el adhesivo con mucho cuidado y proceder a colocarle el transparente, de esta manera las Calco manías quedan selladas con el transparente. Un ratito al Sol y Listo mi gente... 👍👍👍 Como el transparente es bastante delicado de aplicar le dije a un hermano en la fe, el cual es un maestro en este Arte, todo un Profesional, Dios bendiga a mi hermano Camilo 👍👍.
Que me ayudara a aplicar el transparente 👍👍👍. Y como se puede apreciar en las imágenes el trabajo quedo Perfecto gracias a Dios... Aleluya!!!!! Que Bendición de verdad.
Espero sea de su agrado esta publicación, y gracias por visitar mi Blog. Shalom.
Among the materials used I forgot to mention the transparent 🤣, finished the finishing process to paint, I waited for a day with good sunshine and so it was .... The big day arrived 😁😁, to paint. The paint was prepared with the Tinel, the compressor was turned on and paint, first the bottom of the tank and then the top, simultaneously the first coat was placed to the mud guard and lids 👍👍👍👍, while drying the first coat in the tank ... After drying the second coat was given, once dry proceeded to remove the adhesive with great care and proceed to place the transparent, in this way the Calco manias are sealed with the transparent. A little while in the sun and ready my people... 👍👍👍👍 As the transparent is quite delicate to apply I told a brother in the faith, which is a master in this art, a professional, God bless my brother Camilo 👍👍👍.
Who will help me to apply the transparent 👍👍👍👍. And as you can see in the pictures the work was perfect thanks to God.... Hallelujah!!!!! What a blessing indeed.
I hope you like this publication, and thank you for visiting my Blog. Shalom.
Translated with https://www.deepl.com/translator
Todas las imágenes son de mi autoría, capturadas con mi teléfono ZTE.
All images are my own, captured with my ZTE phone.