Saludos amigos de Hive Diy, sean bienvenidos a mi blog, hoy martes quiero desearles lo mejor que sus días sean bendecidos en salud, prosperidad y en todo lo que se propongan, el día de hoy una vez compartiendo una nueva idea creativa en limpiapipas.
Greetings friends of Hive DIY, welcome to my blog. Today, Tuesday, I want to wish you all the best and that your days are blessed with health, prosperity, and success in everything you set out to do. Today, I'm sharing a new creative idea using pipe cleaners.
En esta oportunidad se trata de una figura de ave inspirada en el Carbonero blanco de Splinterlands, esta carta representa un ave de color blanco que a simple vista se ve muy tierna y bonita, supe que es una buena idea de recrear utilizando este material.
This time it's a bird figure inspired by the Great Tit from Splinterlands. This card represents a white bird that at first glance looks very cute and pretty, and I knew it was a good idea to recreate it using this material.
El proceso es sencillo y solo vamos a utilizar dos colores de limpiapipas, a continuación les muestro el proceso y los materiales que utilicé, verán que es fácil así guarden este tutorial por si lo quieren intentar.
The process is simple and we're only going to use two colors of pipe cleaners. Below I'll show you the process and the materials I used. You'll see it's easy, so save this tutorial in case you want to try it.
| Materiales | Materials |
|---|---|
| Limpiapipas blanco, naranja, marrón, gris | White, orange, brown, gray pipe cleaners |
| Tijera, silicón | Scissors, silicone |
| Servilletas | Napkins |
| Ojitos móviles, encendedor | Googly eyes, lighter |
Paso a paso / Step by step
El primer paso que vamos a realizar será armar lo que sería la base de nuestra ave, voy a tomar un limpiapipas blanco, doblaremos en la mitad y medimos con la cinta métrica 6 cm, giramos dos veces y unimos las puntas sobrantes. Realizamos dos piezas de estas.
The first step we're going to take is to assemble what will be the base of our bird. I'm going to take a white pipe cleaner, fold it in half, and measure 6 cm with the measuring tape. We'll twist it twice and join the remaining ends. We'll make two of these pieces.
Luego vamos a tomar una pieza y con ayuda de los dedos doblamos un poco la punta, hacia afuera y el centro hacia el medio, la otra pieza la punta hacia abajo, doblamos en el centro y en el final un relieve.
Realizamos el pico con limpiapipas marrón y unimos ambas piezas, en el centro colocamos papel o servilletas para rellenar, luego vamos a tomar otros dos limpiapipas realizamos de nuevo como en el primer paso y cubrimos los laterales de acuerdo a la forma.
Next, we'll take one piece and, using our fingers, gently fold the tip outwards and the center towards the middle. With the other piece, fold the tip down, fold it in the center, and create a raised edge at the end.
We'll make the beak with brown pipe cleaners and join both pieces. We'll place paper or napkins in the center for stuffing. Then, we'll take two more pipe cleaners and repeat the first step, covering the sides according to the shape.
Ahora vamos a realizar las alas para ambos lados, debes tomar dos limpiapipas y en cada uno realizar tres dobles, recortar y pegar, también realicé uno igual para la cola pero más pequeño.
Now we're going to make the wings for both sides. You need to take two pipe cleaners and make three folds in each one, cut and glue them. I also made one the same way for the tail, but smaller.
Luego cortamos tres piezas pequeñas de limpiapipas naranja, unimos y en la parte inferior separamos y debemos quemar un poco el limpiapipas con un encendedor para formar las patitas, luego pegamos los ojitos móviles y en las mejillas el limpiapipas naranja también.
Next, we cut three small pieces of orange pipe cleaner, join them together, and at the bottom we separate them and we must burn the pipe cleaner a little with a lighter to form the legs, then we glue on the googly eyes and the orange pipe cleaner on the cheeks as well.
Por último colocamos en el pico la rama que lleva en la foto original, utilicé limpiapipas blanca y lo pintamos con sombra para dar tono gris, y listo, de esta forma terminé esta linda figura inspirada en el Carbonero blanco.
Finally, we placed the branch it carries in the original photo on its beak. I used white pipe cleaners and painted it with shadow to give it a gray tone, and that's it! This is how I finished this cute figure inspired by the Great Tit.
Espero les haya gustado el resultado, muchas gracias por el apoyo y por visitar mi publicación, nos vemos en una próxima oportunidad con más ideas creativas.
I hope you liked the result, thank you so much for your support and for visiting my post, see you next time with more creative ideas.
Más del resultado final:
More on the final result: