🌹💖🌹HERMOSO ORGANIZADOR ELABORADO CON MATERIALES DE PROVECHO PASO A PASO.🌹💖🌹

Hello hive people, especially to my beautiful creative bees of this beautiful community that gives us the opportunity to express ourselves through our art.

For today I bring you an interesting and creative idea that we can develop at home helping us to let flow all that creativity that I'm sure we have inside, although this project is not only about doing a job but we are also giving use to that useful material that if we discard it will only be garbage but we will be able to give life to it.

This time we are going to make a cute Cinderella-themed organizer that can be used for the princesses of the house, to organize their pigtails, or their colors, tempera, etc. in short, to keep order in their belongings, so my loves without further ado, let's get to work.

To start we are going to cut the box because the one I got was too big, then we are going to help us with the ruler and the pen to mark where we want to cut, I marked about 15 cm wide to make my organizer, I did not want to make it so big but you can make it the size you want.

Once marked we take the blade and cut, then with the scissors we cut any excess that we have left when we chopped the box with the blade.

Then we take the stapler and we are going to staple the flaps of the box, making sure that they are well sealed.

Then with the leftovers of the box we will form a smaller box, which will serve as the drawer of our organizer.

Now that the box is well fixed and with the measurements we want, let's proceed with the next step, take the metallic wrapping paper and use the silicone to completely line the entire box, both inside and outside.

For this work use two sheets of paper, as for the wrapping paper does not need to be metallized, it can be the motif you want, as long as it serves to cover the box and gives it a nice look, we must also remember that if we are going to make it for a girl we can line it with a paper of a comic book character.

Now we are going to take the drawer we made in step 3 and proceed to line it, only this time we will do it with a unicolor construction paper, in this case we will use an apple green to make it stand out and look more striking since the paper we used to line the box is very light colored.

Then we take a white cardboard and mark a square the size of the drawer, which we will cut out.

Once cut out, apply cold silicone to the bottom of the drawer and glue the white cardboard to it.

Then on the frosted cardboard we mark a line about 1 cm wide, covering the length of the drawer, then we cut and apply silicone around the edge and glue the frosted cardboard strip.

Then cut out two rectangles about 15 cm wide and the length of the box, this can be done with the leftovers of the box.

When we have already cut out we take a white cardboard and on it we mark the rectangle that we took out of cardboard, but we must leave a few millimeters more so that it protrudes from the piece of cardboard.

Once all the pieces are ready, we take the cardboard rectangle and apply the silicone and then place the cardboard piece on top of it, leaving the two pieces completely lined and ready.

We mark on the frosted cardboard a line of approximately 0.50 cm wide when we cut it out, we put a little silicone on the edge of the pieces we made in step 7.

In this step we are going to assemble all the pieces we have previously made, so we take the piece of the drawer we made and place it inside the big piece, as you can see in the picture.

Then we will do the same with the other pieces to which I put silicone on the sides and glue them to the big piece.

Then take the frosted cardboard and mark the strip half a centimeter wide and 25 cm long, which you cut out.

Then put a little cold silicone on the tip and begin to roll, while we are rolling we are placing silicone to be fixed, at the end in the same cardboard cut a kind of flower, which paste over the rolled piece we did, this will serve as knob drawer organizer, can enough silicone and stick to the piece of the drawer in the center.

Take the figure that I printed in icing paper and cut it out, this time I did Cinderella but you can do the character you want, cut out both the figure of the doll and the flowers and apply a little bit of cold silicone and glue it on the organizer, the flowers I glued them in the drawer to distribute the decorations throughout our project.

Finally we are giving it the final decorative touches so I took the flower applications and placed them, some on the drawer knob and others in different areas of the organizer.

Well my loves this is all for today hoping that you liked the final result of the organizer, this is an easy project and has many utilities, so it is a manual work of profit, so I invite you to put in place that cute little hands, I invite you to let your creativity flow, and let your imagination fly, for sure you will have beautiful results like the one I show you in my project, if you really liked my post I invite you to vote, reblog and leave me your comment that is very important to me, and thank you very much in advance.

📱 All photos were taken with my Xiaomi readmi 9T phone and are my property, use Deepl translator and polish program for editing them.