Hola a todos, estimados amigos de esta hermosa plataforma, por fin un descanso, me refiero a que sali un poco de la cocina jajajaja, pero bueno es por fuerza mayor, con esto quiero decir que me hacia falta una escalera de tres metros, para limpiar el techo o sea las canaleta, entonces sin dudarlo puse manos a la obra y lo primero para estos casos es comprar el hierro que vamos a utilizar, entonces para los costados hierro de 30 x 30 y para los escalones de 30 x 20, mas los electrodos y a trabajar, que es lo que mas me agrada y para mi es una rutina siempre.
En base a mis conocimientos de herreria en la parte de abajo de dicha escalera, le solde unos chapones encurbados, a los que luego le coloque con tornillos caucho de cubierta de motocicleta, es para que tenga mejor agarre.
Como les habia comentado amigos, una ves comprado el hierro y cortado a la medida que necesito, como la varilla entera es de 6 metros de largo y la escalera la necesito de 3 metros corte por la mitad y los escalones a 30 centimetros cada uno.
Asi que teniendo los laterales y haber medido todo como dije quedaria el espacio de 30 x 30, fui soldando los escalones, primero de un lado y luego del otro.
Como siempre es mi costumbre manifestarme diciendo QUE SI TODO LO QUE HACEMOS, LO HACEMOS CON MUCHO AMOR Y PERSEVERANCIA, LAS COSAS SALEN MUY BIEN, entonces puse en pratica todo de mi y lo que aprendi.
La verdad amigos justo es un dia de mucho calor, asi que todo bien con la vestimenta para este trabajo, ecepto los pies jajajaja, bueno siempre con mucha precaucion, el tema es armar la escalera.
Como la que se puede ver en la primera foto de esta publicacion, luego de efectuarle los retoques me quedaria solamente pintarla muy bien para evitar el oxido y asi la misma tendria mas duracion.
MUCHAS GRACIAS POR SEGUIRME Y LEERME, QUE PASEN UN BELLO DIA.
ENGLISH
Hello everyone, dear friends of this beautiful platform, finally a break, I mean that I left the kitchen a little hahahaha, but well it is by force majeure, by this I mean that I needed a ladder of three meters, to clean the roof or the gutters, so without hesitation I got down to work and the first thing for these cases is to buy the iron that we will use, then for the sides iron 30 x 30 and for the steps 30 x 20, plus the electrodes and to work, which is what I like the most and for me is always a routine.
Based on my knowledge of blacksmithing at the bottom of the staircase, I welded a few plates encurbados, which I then placed with screws motorcycle tire rubber, is to have better grip.
As I had told you friends, once bought the iron and cut to the size I need, as the entire rod is 6 meters long and the ladder I need 3 meters cut in half and the steps to 30 centimeters each.
So having the sides and having measured everything as I said the space of 30 x 30 would be, I welded the steps, first on one side and then on the other.
As it is always my custom to say that if everything we do, we do it with a lot of love and perseverance, things go very well, so I put into practice everything I have learned.
The truth friends is just a very hot day, so everything is fine with the clothes for this job, except the feet hahahaha, well always with caution, the issue is to assemble the ladder.
Like the one you can see in the first picture of this publication, after making the touches I would only paint it very well to avoid rust and thus the same would have more durability.
THANK YOU VERY MUCH FOR FOLLOWING AND READING ME, HAVE A NICE DAY.