English
🎮Repairing Classic Xbox Controller🎮
Hello Hive family and Gamers brothers, you know I'm a video game console lover, I'm also a collector of desktop console controllers, in my room, I have too many controllers and all of them are different. I have been doing this since the beginning of the year, I wonder how I will end up in December this year with so many console controllers.
My classic Xbox has four different controllers, one of them is a white one, the casing I painted myself, maybe not with the best paint material, my goal was to make it look different from the rest of the controllers I own. One thing I didn't say is that the controller I painted white didn't work, it needed special maintenance.
The controller connected to the Xbox intermittently, it connected and disconnected successively, this is a very common problem of the controllers of this console, the cables tend to fail quite a lot with time, even more, if we keep our controller in a drawer for a long time. When I bought my Xbox, I had four controllers, only one of them worked, the others were not working due to cable problems, it impresses me that a controller and its cable that have been long stored in a bag in a drawer is still operational.
Another problem that this controller has is that the left trigger was loose because its tracks were raised, therefore, the trigger did not work. The last thing that failed at times was the joystick, it had the bad habit of going sideways when a player moved the joystick abruptly, but I tell you right now that it was the easiest problem to solve.
Next, I will show you the tools I used to repair my classic white Xbox controller, to disassemble the controller just use a small fluted screwdriver, Xbox controllers have seven screws, four on the sides, one on the top and one on the bottom.
Alcohol and a toothbrush (not in use) to clean the controller's electronic board.
A washing brush and soap to wash the housing parts, levers, and buttons.
A soldering iron, a tin sucker, tin, a copper wire, and a good condition wire from another Xbox controller.
Now let's get started:
The first thing we are going to do is to remove the label that has the controller to remove the screw that is under there, once the seven screws are removed with the slotted screwdriver, we carefully disassemble the parts of the housing.
I realized that disassemble a classic Xbox controller is easier than it seems, it helps a lot the fact that the triggers are directly soldered on the plate, so I would not have the typical inconvenience of arms the triggers to fit well in the holes that correspond to them.
Unlike the PlayStation controllers that you have to take special care on the top buttons, if we are not careful the sheet that causes the contacts can be bent or even cut and a minimum rose will cause us to run out of "L1", "L2, "R1" and "R2". The most problematic thing to remove is the crosshead, I don't disassemble it because I'm afraid of losing the small screws.
Well once I disassemble the control the first thing, I do is to clean the board with the toothbrush, first I do it with the dry brush, so I remove the dust faster, brushing the two levers that could be noticed that had some wear, brushing the triggers, brushing the tracks and the processor of the electronic board of the control.
Then we use alcohol to, now yes, clean the board well so that no dirt makes contact with the tracks and affect the performance of the control, you must brush carefully and not with a lot of alcohol, this procedure is mainly to restore the levers without replacing the stick of the control board.
When I finished using the alcohol, I waited for the board to dry for an hour to test it on my Xbox test controller, as I imagined, in the stick, there was no problem, but the controller still had connection problems, it connected and disconnected in succession. Also, the right trigger (the one behind the main joystick) was not working.
Checking I noticed that the trigger tracks were up, for a matter of securing things I took the liberty of experimenting with several spare controls I have, I learned the basics of soldering thanks to this situation.
I took the liberty of using one of the controls that no longer work to remove one of those triggers that does work to install it on the board that is in good condition.
I took out the good trigger and removed the bad trigger from the board of my control, to be able to remove the solder from the trigger I had to use the soldering iron and put it on the solder to melt and with a tin sucker, we put it on the solder that is hot and with a quick movement we can suck the tin that is there so that the pins are free, so they can leave the board without problems. Something important, if you are right-handed, I recommend you to use the solder sucker in your left hand so that in the right hand you can use the soldering iron without burning your fingers.
The installation of the trigger will be a bit tricky, as the leads are raised, so I will use a trick, on the second soldering of the trigger there is a path that leads to a fence, that point must be scratched with a needle so that the copper can be found from the outside and so the tin will adhere to that point, Once we have the point with tin we will introduce the copper wire that will do the function of bridge between the second soldering of the trigger and the point, it is necessary to have too much precision, it cost me a lot of work to do it but it was possible to obtain it.
To finish with the board and only remains to replace the cable, so carefully remove the solder joints with the suction to remove the bad cable, we look for the good cable (which I took from another control that I had as spare).
Now we introduce the pins of the cable, the red cable always has to be down, unless they have another type of plate, in that case, it would be the other way around, we have to fit at least the first five pins so that the control can work, in case we already have the pins in the position we proceed to solder and ready.
Note: if the tracks where they go the soldering of the cable are raised, unfortunately, the control will not work again.
As for the casing, I washed it and put it to dry for about four hours, then I painted it and the controller was spectacular. That's how I repaired my classic Xbox controller, now I have four controllers in my favorite console.
I hope you liked this post, and without anything else to say, I'll see you family.
Greetings and blessings.😃
Thank you very much!!
Translated with www.DeepL.com/Translator
🎮Reparando Mando de Xbox clásico🎮
Hola familia de Hive y hermanos Gamers, saben que soy un amante de las videoconsolas, también soy un coleccionista de mandos de consolas de sobremesa, en mi habitación tengo demasiados mandos y todos son distintos. Llevo haciendo esto desde que empezó el año, me pregunto como terminaré en diciembre de este año con tanto mando de consola.
Mi Xbox clásica tiene cuatro controles distintos, uno de ellos es uno blanco, la carcasa la pinté yo mismo, tal vez no con el mejor material de pintura, mi objetivo era que se viera diferente al resto de mandos que poseo. Una cosa que no dije es que ese mando que pinté de blanco no funcionaba, necesitaba un mantenimiento especial.
El mando se conectaba al Xbox de forma intermitente, se conectaba y se desconectaba sucesivamente, esto es un problema muy común de los mandos de esta consola, los cables suelen fallar bastante con el paso del tiempo, más aún si guardamos nuestro mando en un cajón por mucho tiempo. Cuando volví adquirir mi Xbox tenía cuatro mandos, tan sólo uno de ellos funcionaba, los demás por problemas de cable no sirvieron, me impresiona que un mando y su cable que han estado mucho tiempo guardados en una bolsa dentro de un cajón siga operativo.
Otro problema que este mando tiene es el gatillo izquierdo estaba flojo porque sus pistas estaban levantadas, por ende, no funcionaba el gatillo. La última cosa que fallaba por momentos era la palanca, tenía la mala costumbre de irse de lado cuando un jugador movía la palanca de forma brusca, pero desde ya les digo que fue el problema más fácil de resolver.
A continuación, les mostraré las herramientas que usé para reparar mi mando de Xbox clásico de color blanco, para desarmar el control basta con usar un destornillador pequeño de estrías, los mandos de Xbox tienen siete tornillos, cuatro en los costados, uno arriba y otro por abajo.
Alcohol y un cepillo de dientes (que no esté en uso) para limpiar la placa electrónica del control.
Un cepillo de lavar y jabón para lavar lo que es las partes de la carcasa, las palancas y los botones.
Un cautín para soldar, un succionador de estaño, estaño, un alambre de cobre y un cable en buen estado de otro mando de Xbox.
Ahora sí empecemos:
Lo primero que vamos hacer es quitarle la etiqueta que tiene el mando para poder sacar el tornillo que está ahí debajo, una vez sacados los siete tornillos con el destornillador de estrías, desarmamos con cuidado las partes de la carcasa.
Me di cuenta que desarmar un mando de Xbox clásico es más fácil de lo que parece, ayuda mucho el hecho de que los gatillos estén directamente soldados en la placa, así no tendría el típico inconveniente de armas los gatillos para que encajen bien en los huecos que les corresponden.
A diferencia de los mandos de PlayStation que hay que tener un especial cuidado en los botones de arriba, si no tenemos cuidado la lamina que provoca los contactos se puede doblar o incluso cortar y un mínimo rose provocará que nos quedemos sin “L1”, “L2, “R1” y “R2. Lo más problemático de sacar es la cruceta, no la desarmo porque me da miedo perder los tornillos pequeños.
Bueno una vez que desarmo el control lo primero que hago es limpiar la placa con el cepillo de dientes, primero lo hago con el cepillo seco, así quito el polvo más rápido, cepillando las dos palancas que se podía notar que tenían cierto desgaste, cepillando los gatillos, cepillando las pistas y el procesador de la placa electrónica del control.
Luego usamos alcohol para, ahora sí, limpiar bien la placa para que ningún sucio haga contacto con las pistas y afecte el rendimiento del control, deben cepillar con cuidado y no con mucha cantidad de alcohol, este procedimiento es sobre todo para restaurar las palancas sin necesidad de remplazar el stick de la placa del control.
Cuando termine de usar el alcohol esperé a que se secara la placa por una hora para probarla en mi test controller de Xbox, como me lo imaginé, en la palanca ya no había problema, pero el control aún tenía problemas de conexión, se conectaba y desconectaba de manera sucesiva. Aparte el gatillo derecho (el que está atrás de la palanca principal) no estaba funcionando.
Revisando me percaté de que las pistas del gatillo estaban levantadas, por una cuestión de asegurar las cosas me tome la libertad de experimentar con varios controles que tengo de repuesto, aprendí lo básico para soldar gracias a esta situación.
Me tomé la libertad de usar uno de los controles que ya no sirven para sacar uno de esos gatillos que si funciona para instalarlo en la placa que si está en pleno buen estado.
Saqué el gatillo bueno y saqué en gatillo malo de la placa de mi control, para poder sacar las soldaduras del gatillo tuve que usar el cautín y ponerlo sobre la soldadura para que se derrita y con un succionador de estaño lo ponemos sobre la soldadura que está caliente y con un movimiento rápido podemos succionar el estaño que está ahí para qué los pines queden libres, así podrán salir sin problemas de la placa. Algo importante, si eres diestro te recomiendo que uses el succionar de estaño en tu mano izquierda, para que en la derecha puedas usar el cautín si quemarte los dedos.
La instalación del gatillo será un poco complicada, ya que las pistas están levantas, así que usaré un truco, en la segunda soldadura del gatillo hay un camino que conduce a un cercado, ese punto hay que rayarlo con una aguja para que el cobre se pueda encontrar desde afuera y así el estaño se adhiera a ese punto, hay que hacer esto con muchísimo cuidado para no dañar la placa, una vez que ya tenemos el punto con estaño introduciremos el alambre de cobre que hará la función de puente entre la segunda soldadura del gatillo y el punto, hay que tener demasiada precisión, me costó mucho trabajo hacerlo pero se pudo conseguir.
Para acabar con la placa ya sólo queda remplazar el cable, así que con cuidado retiramos las soldaduras con el succionador para sacar el cable malo, buscamos el cable bueno (que lo saqué de otro control que tenía de repuesto).
Ahora introducimos los pines del cable, el cable rojo siempre tiene que estar hacia abajo, al menos que tengan otro tipo de placa, en ese caso sería al revés, tenemos que encajar al menos los primeros cinco pines para que el control pueda funcionar, en caso de que ya tengamos los pines en posición procedemos a soldar y listo.
Nota: si las pistas donde van las soldaduras del cable están levantadas, lamentablemente el control no volverá a funcionar.
En cuanto a la carcasa pues la lavé y la puse a secar por unas cuatro horas, luego la pinté y el mando me quedó espectacular. Así fue como reparé mi mando de Xbox clásico, ahora tengo cuatro controles en mi consola preferida.
Espero que les haya gustado este post, y sin nada más que decir nos vemos familia.