Do you want to learn how to make some simple and practical pot holders?

I will show you an easy way to do them and you will see how in such a short time you will get some beautiful and useful utensils that will help you simplify your work and also beautify your kitchen.

Luego de un tiempo, y por algunos inconvenientes de internet, regreso a la plataforma gracias a la ayuda de mi hija Hive account@dianakyv, quien me oriente en ñas publicaciones y me anima a participar en la colmena.

After a while, and due to some internet problems, I return to the platform thanks to the help of my daughter Hive account@dianakyv, who guides me in the publications and encourages me to participate in the hive .

Manos a la obra !!!

Let's do it !!!

Materiales para este proyecto!!!

Materials for this project !!!

1- Tela estampada y tela unicolor
2- Guata o fieltro o neopreno cualquiera de estos nos servirá para acolchar la pieza
3- Sesgo de Ancho que combine con las telas escogidas.
4- Regla (para trazar el patrón)
5- Una hoja carta
6- Lápiz, tijera, alfileres o ganchos para costura, hilos y obviamente una máquina de coser.

1- Printed fabric and unicolor fabric
2- Wadding or felt or neoprene, any of these will serve to pad the piece
3- Width bias that matches the chosen fabrics.
4- Ruler (to draw the pattern)
5- A letter sheet
6- Pencil, scissors, pins or hooks for sewing, threads and obviously a sewing machine.

Elaboración del patrón

Elaboration of the pattern

Take a blank sheet and make a rectangle measuring 22cm x 13cm, which will be folded in half leaving 11cm on each side and will be folded across so that the sheet is divided in 6.5 Cms above and below.

![FOTO 1.jpg](

This last measure is for drawing an end-to-end mark. This line is made as a reference line to later trace the shape for the pot gripper. Once this is done then we are going to fold the paper in half, remaining in two parts of 11cms each, it will be measured from the opposite side to the fold 3cms inwards.

From that mark we are going to give it the rounded shape as seen in the photo, passing through the center line down and giving it a more round shape at the bottom, leaving it Cut out the three fabrics that we will use, in the next image you will see how they should be.

Now we are going to join the pieces, so that the neoprene, felt or wadding (whichever you want to use) was in the center between the two fabrics.

Once this is done, proceed to sew with a straight seam around it, remaining as follows.

Un lado estampado y del otro lado unicolor

One side printed and one side solid

Ahora vamos a proceder a coser el sesgo alrededor de las piezas ya unidas

Now we are going to proceed to sew the bias around the already joined pieces

*** Ahora procedemos a voltear el sesgo y repasar la costura con zigzag***

Now we proceed to flip the bias and go over the stitching with zigzag

Ahora procedemos a doblar la pieza por la mitad una vez cosido el sesgo

Now we proceed to fold the piece in half once the bias is sewn

We are going to sew a piece of bias about 8 Cms that we are going to fold later and we are going to place it at the end of the fold and then sew with a straight seam attached to the edge of the bias until the center of the piece as shown in the image above with the orange lines.

In this way it is sewn up to approximately half, in the same way it will be done with the other handle and ready we have finished our project.

Espero que te haya gustado este proyecto fácil y sencillo de hacer y que sea de utilidad para ti, cualquier duda no dudes en comentar! GRACIAS!!!

I hope you liked this easy and simple project to do and that it is useful for you, any questions do not hesitate to comment! THANK YOU!!!

Todas las imágenes son de mi propiedad tomadas desde mi dispositivo móvil
All images are my property taken from my mobile device