El día de hoy quiero mostrarles como hice una máquina casera para derretir cera, basada en el uso estético para la depilación corporal.
Para llevar este procesó a cabo solo hace falta calentar constantemente la cera para que su estado pase de solido a liquido y pueda ser aplicada, vamos a elaborar una maquina bastante simple pero funcional, si la hacemos con materiales reciclados pero de buena calidad, no hay duda que la maquina tendrá una larga vida útil.
Good day friends of #hive, I hope you are very well!!
Today I want to show you how I made a homemade machine to melt wax, based on aesthetic use for body waxing.
To carry out this process, it is only necessary to constantly heat the wax so that its state goes from solid to liquid and can be applied, we are going to make a fairly simple but functional machine, if we make it with recycled materials but of good quality, there is no doubt that the machine will have a long service life.
Lo esencial es conseguir dos recipientes de aluminio que encajen uno en el otro, pueden ser latas de gran tamaño.
Una vez que tengamos los recipientes los demas materiales seran faciles de conseguir; Yo utilicé una lata de repuesto de carro, donde vienen las pilas de gasolina y otra mas pequeña de nescafé que calzaba perfectamente encima de la mas grande. Los otros materiales serian, un bombillo, cable con conector, interruptor de encendido y base para el bombillo.
The first thing is to have all the materials, we must look for alternatives since I do not think that we all have the same things at home, mainly packaging.
The essential thing is to get two aluminum containers that fit one in the other, they can be large cans.
Once we have the containers the other materials will be easy to get; I used a spare car can, where the gasoline batteries come, and a smaller one made of nescafé that fit perfectly on top of the larger one. The other materials would be, a light bulb, cable with connector, ignition switch and base for the light bulb.
Yo antes de empezar la instalación, tome la lata mas grande y le pegue un pedazo de foami, lo hice de primero ya que hay que dejarlo secar.
Como pueden ver en la lata le hice un hueco del tamaño del interruptor de encendido y otro hueco por la parte de atras donde entrará el cable de la corriente.
Once we have all the materials we can start.
Before starting the installation, I took the largest can and glued a piece of foam to it, I did it first since you have to let it dry.
As you can see in the can I made a hole the size of the ignition switch and another hole in the back where the power cable will enter.
Esta parte puede ser la mas importante de la máquina, debemos deja todo muy bien conectado para que no fallé en ningun momento.
Debemos tener en cuenta que el espacio es reducido y debemos tener paciencia en la instalación; Por la parte de atrás introducimos el cable con conector y una punta la pegaremos al interruptor, la otra punta irá directa a la base del bombillo, el cable restante de la base del bombillo irá al otro contacto del interruptor y ya tendremos nuestro circuito armador. No es nada complicada y cualquiera de nosotro puede hacerlo, solo debemos asegurarnos de que queden fijas las uniones y bien aisladas con cinta protectora.
It is time to install the electrical circuit.
This part may be the most important of the machine, we must leave everything very well connected so that I do not fail at any time.
We must bear in mind that space is limited and we must be patient when installing; From the back we introduce the cable with connector and one end will be glued to the switch, the other end will go directly to the base of the bulb, the remaining cable from the base of the bulb will go to the other contact of the switch and we will have our assembly circuit. It is not complicated at all and any of us can do it, we just have to make sure that the joints are fixed and well insulated with protective tape.
De igual manera utilicé cinta para fijar los cables al fondo de la lata, lo mas lejos posible del calor del bombillo y sin que ningún cable haga un mal contactó para no provocar un cortó circuito.
Por otro lado la base del bombillo la uní con una platina al costado de la lata, simplemente use dos tornillos pequeños y ya quedo, recuenden medir y dejar el espacio suficiente para los cables de abajo, tambien hay que tener en cuenta que el bombillo no toque la lata de arriba, siempre dejando un espacio prudente.
In this photo you can see the circuit inside the can.
In the same way I used tape to fix the cables to the bottom of the can, as far as possible from the heat of the bulb and without any cable making a bad contact so as not to cause a short circuit.
On the other hand, I joined the base of the light bulb with a plate on the side of the can, just use two small screws and that's it, remember to measure and leave enough space for the cables below, you also have to take into account that the light bulb does not touch the top can, always leaving a safe space.
Recomiendo pulsar el interruptor varias veces y mover el cable trasero a ver si todo esta ajustado.
Si el bombillo es de luz amarilla mucho mejor, estos calientan mas y debemos tener un calor que pueda derretir la cera rápidamente para que su tiempo de uso no sea tan prolongado, no queremos que el bombillo dure tanto tiempo encendido sino terminaría quemandose.
Once we check everything and it is correctly, it only remains to put the light bulb and test if it works.
I recommend pressing the switch several times and moving the rear cable to see if everything is adjusted.
If the bulb is yellow light much better, they heat more and we must have a heat that can melt the wax quickly so that its use time is not so long, we do not want the bulb to last so long on, otherwise it would end up burning.
Con una paleta revolvemos constantemente hasta que el producto pase a ser liquido.
La finalidad del foami es poder tomar la lata sin quemarnos, se calienta bastante y queremos manipularla maquina para tener mas seguridad con la cera; Al final podemos forrar nuestra maquina a nuestro gusto, yo no lo hice para que puedan apreciar mejor el desarrollo, pero ya solo quedaría a su #creatividad el resultado final.
It only remains to put the can on top and apply some wax to it.
With a trowel we constantly stir until the product becomes liquid.
The purpose of the foami is to be able to take the can without burning ourselves, it gets quite hot and we want to manipulate it by machine to have more security with the wax; In the end we can cover our machine to our liking, I did not do it so that they can better appreciate the development, but the final result would only be left to their #creativity.
Se que a todas la mujeres le encantara la idea y espero puedan lograr sus maquinas personalizadas.
Todas las fotos son de mi propiedad
This was it, I hope you liked it, as always a pleasure to share my projects with you.
I know that all women will love the idea and I hope they can achieve their custom machines.
All photos are my property
Gracias por llegar hasta aqui, que tengan un felíz día!!
Thanks for getting here, have a happy day!!