Hola a todos, en mis post anteriores donde hacie referencia de las columnas que estaba colocando para el futuro garge, bueno amigos esta son fotos de la continuacion, como dice el titulo terminando la pared para la caida del techo, que por supuesto es todo un tinglado con hierros (c) y hierros (u), para luego seguir el mismo al colocar las chapas.
Como lo demuestra la fotografia, con mucha paciencia y perseverancia, como o digo siempre, hago los trabajos muy tranquilo y por supuesto yo solo, lo bueno de esto que el subir y bajar el andamio, les digo que es una buena gimnasia jajaja.
Lo primero como les decia es haber terminado el encadenado arriba del muro, luego la pared que me falta para la haltura que seria unos 90 centimetros, para despues llenar las columnas arriba del mismo.
Bueno siempre sale alguna foto, asi, pero el detalle es porque a esa hora de la tarde termine la pared y por supuesto con mucho calor jajajaja.
En esta fotografia se puede apreciar lo que les comentaba referente a las columnas, donde tiene un hierro en la parte de arriba, es un hierro (u) el cual hace de viga tapando las columnas que son tubos de 100 mm., por supuesto amigos todos soldado.
Como pueden ver los hierros (c) que les comente, los mismos van amurados en el muro y soldados en la viga (u) y lo que estoy haciendo en este momento es presentando lo hierros (u) don van atornilladas las chapas.
Por supuesto que esta parte en donde se colocan estos hieron en la medida que se puede tienen que estar las medidas muy bien, para que luego al colocar las chapas no tengamos sorpresas.
Cuando digo sorpresas me refiero a que este fuera de escuadra, luego de soldar todo lo que seria los hierros, los pinto muy bien con antioxido, para luego una ves al estar todo muy bien recien comenzar a techar, seria en otra publicacion jajaja ( AMIGOS LA VINCHA BLANCA NO ES LA DE RAMBO JAJAJA, ES PARA QUE AL TRANSPIRAR, NO CORRA EL SUDOR POR MI FRENTE EMPAÑANDO EL ANTEOJO) de igual manera me queda muy bien jajaja.
MUCHAS GRACIAS POR SEGUIRME Y LEERME, QUE TENGAN UN EXCELENTE DIA.
ENGLISH
Hello everyone, in my previous post where I made reference to the columns that I was placing for the future garage, well friends this are photos of the continuation, as the title says finishing the wall for the fall of the roof, which of course is a whole mess with irons (c) and irons (u), and then follow the same when placing the plates.
As the picture shows, with a lot of patience and perseverance, as I always say, I do the work very quietly and of course by myself, the good thing about this is that the up and down the scaffolding, I tell you it's a good gymnastics hahaha.
The first thing as I was saying is to have finished the chaining above the wall, then the wall that I need for the height that would be about 90 centimeters, and then fill the columns above it.
Well always comes out some photo, but the detail is because at that time of the afternoon I finished the wall and of course with a lot of heat hahahaha.
In this picture you can see what I was saying about the columns, where it has an iron at the top, is an iron (u) which makes a beam covering the columns that are 100 mm. tubes, of course friends all welded.
As you can see the irons (c) that I mentioned, the same ones are anchored in the wall and welded in the beam (u) and what I am doing at this moment is presenting the irons (u) where the plates are screwed.
Of course this part where these irons are placed, as far as possible, have to be very well measured, so that later when placing the plates we do not have surprises.
When I say surprises I mean that this out of square, after welding everything that would be the irons, I paint them very well with antirust, and then once everything is very well just start roofing, it would be in another publication hahaha (FRIENDS THE WHITE STRIP IS NOT THAT OF RAMBO HAHAHAHAHAHA, IS SO THAT WHEN SWEATING, DOES NOT RUN THE SWEAT BY MY FRONT EMPAÑANDO THE EYE) anyway I look very good hahaha.
THANK YOU VERY MUCH FOR FOLLOWING ME AND READING ME, HAVE A GREAT DAY.