Hello friends, I hope you are doing great and that you are getting ready to have a great weekend.
Since I moved to my apartment, the closet has always been an issue for me because it was a hole without divisions to place the clothes. To solve the problem and for economy I had to put an Aero Closet that I will tell you later how I put it and it was the best thing I could have done. Obviously at some point in my life I should make the MDF closet but that will be for the future, for the moment I don't need it so much.
Hola amigos, espero estén muy bien y que se estén preparando para pasar un gran fin de semana.
Desde que me mudé a mi departamento, el closet desde siempre ha sido un tema para mí porque era un hueco sin divisiones para colocar la ropa. Para resolver y por economía tuve que poner un Aerocloset que ya luego les contaré cómo lo puse y fue lo mejor que pude haber hecho. Obviamente en algún momento de mi vida debería hacer el closet de MDF pero ya eso será para un futuro, por los momentos no me hace tanta falta.
Already after solving the issue of the divisions to put the clothes, I had another dilemma: the closet is dark because it does not have any kind of light installed and the room light is not enough. Besides that, it seems absurd to me to have to turn on the room light to be able to half-light the closet, because it is really for HALF LIGHTING.
Ya luego de resolver el tema de las divisiones para poner la ropa, tenía otro dilema: el closet es oscuro porque no tiene ningún tipo de luz instalada y la luz de la habitación no es suficiente. Además de eso, me parece absurdo tener que encender la luz de la habitación para poder medio iluminar el closet, porque realmente es para MEDIO ILUMINAR.
So, already a bit exhausted of seeing or lighting with my cell phone, I decided to use again my super led lights, the ones I used for my post to illuminate the stairs Check out this super idea for chill lighting - ENG/ESP. I bought my 5 meter tape again for $5 and got to work.
The first thing I did was to go to the hardware store to buy what I needed:
- A gutter
- No. 14 wire
- An electrical outlet (I needed it simple but as much as I looked for it, I couldn't get it).
With this I was more than ready.
Así que ya un poco agotada de ver o alumbrar con mi celular, decidí utilizar nuevamente mis súper luces led, las que usé para mi publicación de iluminar las escaleras Check out this super idea for chill lighting - ENG/ESP. Compré nuevamente mi cinta que mide 5 metros por 5$ y manos a la obra.
Lo primero que hice fue irme a la ferretería a comprar lo que necesitaba:
- Una canaleta
- Cables nº 14
- Un tomacorriente (lo necesitaba simple pero por más que lo busqué, no pude conseguirlo).
Ya con esto estaba más que lista.
The first thing I did was to turn off the power to the outlets so that an accident would not happen and check with my cell phone charger that there was no power. I had to draw power from the outlet closest to the closet with two wires, one for the phase and one for the negative. In this case it didn't matter which one was which because to plug them into the new socket they can be placed in any position one on each side and that's it.
Lo primero que hice fue cortar la electricidad de los tomacorrientes para que no ocurriera un accidente y comprobar con un cargador de mi celular que no había corriente eléctrica. tuve que sacar corriente del tomacorriente más cercano al closet con dos cables, uno para la fase y otro para el negativo. En este caso no importaba cuál era cual porque para conectarlos en el enchufe nuevo pueden colocarse en cualquier posición uno en cada lado y listo.
I then measured the wires to where I needed to plug in the lights and cut both so I wouldn't be working with so much excess.
The cove I measured where I was going to run the entire cable route and cut them.
I glued them to the wall as well as possible to hide the wires.
Luego medí los cables hasta donde necesitaba enchufar las luces y corté ambos para no trabajar con tanto excedente.
La caleta la medí por donde la iba a pasar todo el recorrido del cable y las corté.
Las pegué a la pared lo mejor posible y así poder disimular los cables.
I tested connecting the wires to the new outlet to see if it was sending electricity and indeed everything was very well connected.
Probé conectando los cables al tomacorriente nuevo a ver si estaba mandando electricidad y efectivamente todo estaba muy bien conectado.
Since I had most of the connection ready, I measured half of the lights and placed them in the middle of the closet so that there would be an equal amount of light on each side. I removed the paper so that the glued side would be free and began to glue the tape from the center to the ends.
Como ya tenía casi toda la conexión lista, medí la mitad de las luces y las coloqué en la mitad del closet para que quedara equitativo el espacio de luz a cada lado. Le quité el papel para que quedara la cara con pega libre y empecé a pegar la cinta desde el centro hasta los extremos.
Once I had it ready, I fixed the socket at the height I needed with some wood screws and attached its protector. I plugged in the lights and they wouldn't turn on, obviously, the electricity was cut off. So I went back to restore it and voila, the closet now had its lighting!
Al tenerla lista, fijé el tomacorriente a la altura que necesitaba con unos tornillos para madera y le coloqué su protector. Enchufé las luces y no prendían, obvio, tenía cortada la electricidad. Así que volví a restaurarla y voilá, el closet ya tenía su iluminación!
Now I only had to set the control to turn them on and off whenever I needed to. I couldn't fix it because I didn't have double-stick tape, so in the meantime, I left it out in the open.
You may wonder why I didn't put a switch, the answer is simple: these lights that I bought, have the particularity that when the electricity goes out, when they come back on, they turn on changing color Red, Green and Blue, so I was still going to need to use the control, besides, this has an off and on button that if I put the lights in yellow, they will stay that way forever.
Ya solo me quedaba fijar el control para apagarlas y prenderlas cada vez que lo necesitara. Eso sí no pude fijarlo porque no tenía cinta doble pega, así que mientras tanto, lo dejé a la vista.
Te preguntarás quizás ¿por qué no le coloqué un switch, la respuesta es sencilla: estas luces que compré, tienen la particularidad de que cuando se le va la electricidad, al volver a tener, se prender cambiando de color Rojo, Verde y Azul, así que igual iba a necesitar usar el control, además, este tiene un botón de apagado y de encendido que si coloco las luces en amarillo, se quedarán así siempre.
And well friends, I hope you liked my post today! I send you many hugs...
Y bueno amigos, espero les haya gustado mi post de hoy! Les mando muchos abrazos..