Happy Hive Day friends!
Short earrings will always be the earrings that every woman should have.
Without a doubt the small earrings are garments that we can adjust in any occasion since they are very versatile to use them.
Today I am going to show you the step by step to make a beautiful small earrings designed with the technique of wire wrap and pearls.
Materials.
- 20 beads
- Copper wire
- Marker or pencil (support)
- Small picket
*Step 1
Take the marker and the copper wire, so that a 3 cm end of copper wire is left.
The copper wire is wound around the marker. This should take the round shape of the marker which will be our support to make the circular area of the tendrils.
Step 2
Make three turns with the copper wire over the marker.
Step 3
Then remove the copper wire coil and make a turn with the wire to join the three circles of wire. Then with the pickaxe proceed to
cut the excess material.
Step 4
In this way we should have the wire support to make the weaving with the beads.
Step 5
Then take a copper wire of approximately 40 cm long and proceed to wind it on the surface of the wire support that has been created. This should be fixed to the structure in such a way that it is tightened with the pickaxe and the material is cut.
Then proceed to insert a bead and roll the material protruding from the bead onto the circular copper wire support.
Step 6
Then you must introduce another bead and in the same way proceed to roll the material on the circular wire surface.
Just make two turns with the copper wire and then insert the bead.
Step 7
Step 8
In this way you can see the process of elaboration, you should continue to introduce a bead after the next turn.
Then the ninth bead is introduced and adjusted a little to give way to the next one.
Finally take the tenth bead and proceed to fill the space on the earring.
Step 10
Then hide the excess material of copper wire on the same structure of the earring in such a way that two turns are made and the excess material is cut.
Step 11
With the copper wire proceed to weave all the hole that provides the structure of the earring. It is going to be weaving this.
Step 12
Here you can see the progress of the weaving of the earring.
In this way the total weave of the earring has been formed.
This is how we have created these beautiful earrings. I hope you like them.
Greetings and I hope you have a good time this weekend.
The images are my own and were taken with a ZTE BLADE phone.
Translator utilization: Deepl
The editing of the photos was done using the Polish Photo Editor application and separators were edited in canva.
Feliz dia amigos de Hive!
Siempre unos zarcillos cortos seran los aretes que toda mujer debe tener.
Sin duda alguna los artes peqeños son prendas que podemos ajustar en cualquier ocasion ya que estos Son muy versatiles para utilizarlos.
El dia de hoy les voy a mostrar el paso a paso para elaborar unos bonitos aeretes pequeños diseñados con la tecnica del alambrismo y perlas.
MATERIALES.
- 20 perlas
- Alambre de Cobre
- Marcador o lapiz ( Soporte)
- Piqueta pequeña
Paso 1
Se Toma el marcador y el alambre de cobre, de tal forma que se deja un extremo de alambre de cobre de 3 cm.
El alambre de cobre se procede a enrrollar sobre el marcador. Este debe tomar la forma redonda del maracador el cual será nuestro soporte para realizar el area circular de los zarcillos.
Paso 2
Se deben realizar tres vueltas con el alambre de cobre sobre el marcador.
Paso 3
Luego se saca el enrrollado de alambre de cobre y se hace una vuelta con el alambre para unir los tres circulos de alambre. Luego con la piqueta se procede a
cortar el material sobrante.
Paso 4
De esta forma nos debe quedar el soporte de alambrado para realizar el tejido con las perlas.
Paso 5
Luego se toma un alambre de cobre de aproximadamente 40 cm de largo y se procede a enrrollarlo sobre la superfice del soporte de alambre que se ha creado. Este se debe fijar en la estructura del tal forma que se aprieta con la piqueta y se corta el material.
Seguidamente se procede a meter una perla y así mismo enrollar el material saliente de la perla sobre el soporte circular de alambre de cobre.
Paso 6
Luego se debe introducir otra de la perlas y de igual forma proceder enrrollar el material en la superficei de alambre circular.
Solo se debe dar dos vueltas con el almbre de cobre y luego introducir la perla.
Paso 7
Paso 8
De esta manera se puede observar el proceo de elaboración, se debe seguir introduciendo un aperla despues de la siguiente vuelta.
Luego se introduce la novena perla y se ajusta esta un poco para dar paso a la siguiente.
Finalmente se toma la décima perla y se procede a llenar el espacio sobre el arete.
Paso 10
Segudamente se esconde el material sobrante de alambre de cobre sobre las misma estructura del arete de tal forma que se dan dos vueltas y se corta el material sobrante.
Paso 11
Con el almbre de cobre se procede a tejer todo el orificio que brinda la estructura del arete. Se va a ir tejiendo esta.
Paso 12
Aqui se puede ver el avance del tejido del arete.
De esta manera se ha formado el tejido total del arete.
Así hemos creado estos lindos aretes. Espero que les gusten.
Saludos y espero la pasen bien en este fin de Semana.
Las imagenes son de mi autoria y fueron Tomadas a traves de un Telefono ZTE BLADE.
Traductor utilizado: Deepl
La edicion de las fotos la realicé mediante la aplicaciones Editor de Fotos Polish y los separadores se editaron en canva.