Hoy les estaré hablando y explicando el paso a paso de cómo hacer unos hermosos y delicados Anillos de alambre en forma de nota musical con una pequeña piedra Marrón dándole un toque sencillo y bonito y fácil de hacer una técnica muy simple con alambre en realidad no sabía mucho como trabajar con el alambrismo pero todo es cuestión de práctica y creatividad que uno se proponga.me siento muy complacida y feliz de poder compartir mis conocimientos con ustedes . De todo corazón les deseo muchos éxitos en cada una de las áreas de sus vidas, que Dios les acompañe siempre y que siempre tengan las mismas ganas de poder realizar todos sus proyectos.
Los materiales Son
- Piqueta
- Piedra verde
- Alambre de Cobre
- tubo de plástico de pintura de labio
A continuación les explicaré el paso a paso .
Paso 1
Lo primero es seleccionar el alambre de cobre una vez ya listo se tiene que medir mínimo ya sea de 12 CM el alambre siempre tiene que quedar algo de largo para que así alcance y debamos picar al final .
En cambio siempre si se pica ante puede quedar mal el anillo y no quedará bien en si lo mejor es que sobre y no que falte .
Primero que todo con el alambre de cobre se agarra y poco a poco se le va dando un giro por el tubo de plástico que en este caso sería uno de pintura de labio girando al menos 2 veces
Paso 2
Una vez listo el alambre lo segundo es que con un círculo de un tubo pequeño hacer la forma del aro y una vez listo tiene que quedar de esta manera todo depende como lo quieran dejar si de dos o tres vueltas .
Paso 3
Se agarra con la piqueta y con la punta que queda del alambre se hace un giro pequeño de esta manera.
Tiene que darle la forma musical o sea la nota y se va girando de arriba hacia abajo que quede en forma de ocho y al final se le hace un giro en el medio para que quede sosteniendo de la base del aro que de allí se hace el otro giro al anillo para así hacer el otro paso.
Paso 4
Todo depende de nosotros si lo queremos con piedras o no yo en esta ocasión use una piedra verde y en el otro anillo use una marrón siempre me ah gustado hacer las cosas diferentes y me encanta realizar los anillos así que todo si quieren o no piedras en sus anillos .
Paso 5
Una vez ya terminado con lo que quede del pedazo de alambre se pone hasta la mitad y se hace un giro de dos vueltas de atrás hacia adelante y una vez ya listas se corta y se aprieta con la piqueta .
De modo que de esta manera queda nuestros anillos lindos y hermosos para usar en toda clase de ocasión y perfecto para estas lindas navidades éxitos a todos y espero que les guste mucho asi como a mí me gustó la realización de estos Anillos
Espero sus comentarios y opiniones acerca de estos Anillos. Me despido de ustedes agradeciendo su receptividad y su gran ayuda dándome las sugerencias y las reglas siempre estando dispuesta a canalizar y captar sus recomendaciones, gracias por esta bonita relación que se ha iniciado en Hive.
Muchas Gracias queridos amigos de Hive.
- las imágenes son de mi autoria y fueron tomadas mediante mi teléfono Alatel 1.
- El traductor utilizado : Deepl traductor
- La edicion de las fotos la realicé mediante la aplicaciones Editor de Fotos Polish y los separadores se editaron en canva.
Today I will be talking and explaining step by step how to make a beautiful and delicate wire rings in the form of musical note with a small brown stone giving a simple and nice touch and easy to make a very simple technique with wire actually did not know much how to work with the wire but it's all about practice and creativity that one is proposed. I am very pleased and happy to share my knowledge with you. From the bottom of my heart I wish you much success in each of the areas of your lives, may God be with you always and may you always have the same desire to be able to carry out all your projects.
***The materials are
- Piqueta
- Green stone
- Copper wire
- Plastic lip paint tube
Below I will explain the step by step .
**Step 1
The first thing is to select the copper wire, once it is ready, you have to measure at least 12 CM. The wire always has to be a little long so that it reaches and we must chop at the end.
On the other hand, if the ring is chopped before it can be bad and it will not look good, the best thing is to have more than enough and not too little.
First of all with the copper wire is grabbed and little by little it is given a twist by the plastic tube that in this case would be one of lip paint turning at least 2 times.
**Step 2
Once the wire is ready the second thing is that with a circle of a small tube to make the shape of the hoop and once ready it has to be like this all depends on how you want to leave it if two or three turns.
**Step 3
Grasp with the pickaxe and with the remaining end of the wire make a small twist like this.
You have to give it the musical form or the note and you turn it up and down so that it remains in the form of an eight and at the end you make a turn in the middle so that it remains holding the base of the ring and from there you make another turn to the ring to make the other step.
**Step 4
It's up to us if we want it with stones or not I used a green stone this time and on the other ring I used a brown one I always like to do things different and I love to make rings so everything if you want stones in your rings or not .
**Step 5
Once finished with what is left of the piece of wire, put it in the middle and make a two turn back and forth and once it is ready, cut it and tighten it with the pickaxe.
So in this way we have our rings nice and beautiful to use in all kinds of occasions and perfect for this nice Christmas. I hope you all like it as much as I liked the realization of these rings.
Uploading IMG_20221213_105744.jpg #82
I look forward to your comments and opinions about these Rings. I say goodbye to you thanking you for your receptivity and your great help giving me the suggestions and rules always being willing to channel and capture your recommendations, thank you for this nice relationship that has started in Hive.
Thank you very much dear friends of Hive.
- the images are of my authorship and were taken using my Alatel 1 phone.
- The translator used : Deepl translator
- The editing of the photos was done using the Polish Photo Editor application and the separators were edited in canva.