Hello artisan friends and creators of this great community, I want to greet you and congratulate you on your beautiful works and contributions. I have been in a bit of poor health since I am under a terrible flu, fortunately I have already been experiencing the worst symptoms and I have been recovering, in the midst of that recovery I began to build a mask for these days of Carnival, although I could not go out to show it off, I wanted to do it anyway. Using Foami rubber or Eva rubber as it is known in other places, I made a mask with some very simple templates, adding details and painting it I made the Punisher logo, the hero of Marvel who punishes criminals. Hope you like.
Hola amigos artesanos y creadores de esta gran comunidad, quiero saludarlos y felicitarlos por sus hermosas obras y contribuciones. He estado un poco mal de salud ya que me encuentro bajo una terrible gripe, afortunadamente ya he ido pasando los peores síntomas y he ido recuperándome, en medio de esa recuperación me puse a construir una máscara para estos días de Carnaval, aunque no pude salir a lucirla, de igual forma quise hacerla. Utilizando goma Foami o goma Eva como es conocida en otros lugares, hice una máscara con unas plantillas muy sencillas, agregándole detalles y pintándola hice el logo de Punisher, el héroe de Marvel que castiga a los criminales. Espero que les guste.
PROCESS
I made some very basic templates, looking at many models of helmets and paintball masks, also some models of tactical masks. The template has a part for the lateral areas and for the upper part of the skull as well as the entire frontal area, which goes from the jaw to the neck, however, since it was very large, I made some adjustments to pass it from case to mask, only with some cuts and new measurements.
Hice unas plantillas muy básicas, fijándome en muchos modelos de cascos y máscaras de paintball, también en algunos modelos de máscaras tácticas. La plantilla cuenta con una parte para las zonas laterales y para la parte de arriba del cráneo como toda la zona frontal, que va desde la quijada hasta el cuello, sin embargo como era muy grande hice algunos ajustes para pasarlo de caso a máscara, solo con algunos cortes y nuevas medidas.
As a material I used foam rubber, I had thought to do it in cardboard, but since I wanted to make the eyes as if it were a real skull, that effect was not going to work out for me, so I used foam rubber two millimeters thick. I took the template of the lateral sides and marked the comma with a pencil and then I was cutting the shape little by little until finishing. In the end I took 4 pieces in total, since the foami, being only two millimeters, the mask was going to come out very weak, so I wanted to add another layer to give it more hardness, hence for each template I doubled, that way remove this part. Then I joined them together and at the end with a little glue I joined that cut that they have there, although I later eliminated that detail.
Como material utilicé goma foami, había pensado hacerlo en cartón, pero como quise hacer los ojos como si fuera un cráneo real, ese efecto no me iba a salir, así que utilicé goma foami de dos milímetros de espesor. Tomé la plantilla de los lados laterales y remarqué la coma con un lápiz y luego fui cortando la forma poco a poco hasta terminar. Al final saqué 4 piezas en total, ya que el fomai al ser de solo dos milímetros la máscara iba a salir muy débil, así que quise juntar otra capa para darle más dureza, de ahí que para cada plantilla hice el doble, de esa manera saque esta parte. Luego las uní entre ellas y al final con un poco de pegamento uní ese corte que traen ahí, aunque luego eliminé ese detalle.
The next step is to make the templates for the part of the face and part of the skull, the template is in two parts because it covers the entire head from the chin to the neck, so it is joined at the ends. When doing so I put the template on the foam rubber, which I had to buy in A4 print size, the largest, in order to be able to use most of it. I also took out 4 patterns, which I joined together and thus I had two sides for this entire area.
El siguiente paso es hacer las plantillas para la parte del rostro y parte del cráneo, la plantilla esta en dos partes porque viene para toda la cabeza desde el mentón hasta el cuello así que va unida en los extremos. Al hacerlo puse la plantilla sobre la goma foami, que tuve que comprarla de tamaño de impresión A4 , la más grande, para así poder utilizar la mayor parte. Tambien saqué 4 patrones, los cuales los uni entre ellos y así tuve dos lados para toda esta zona.
The next step is to join the four patterns made in foami, first one of the longest ones, that is, those of the face and the upper part of the skull, then I glue the lateral areas and one with the ends of the first piece, then I do the same process until I have completed the original shape. As you can see, it was left in the shape of a helmet, at the ends of each pattern I carefully made a 45-degree cut with scissors, I did this to achieve that sharp effect throughout the helmet.
El siguiente paso es unir los cuatros patrones hechos en foami, en primero lugar uno los más largos, es decir, los del rostro y la parte superior del cráneo, después unto con pegamento las zonas laterales y las uno a con los extremos de la primera pieza, despues hago el mismo proceso hasta tener completado la forma original. Como pueden ver, quedó con forma de casco, en los extremos de cada patrón yo hice un corte de 45 grados cuidadosamente con una tijera, esto lo hice para lograr ese efecto filoso por todo el casco..
The foami is very malleable, especially when we can subject it to heat. So, so that the mask would not be so uniform, but with some shapes, I took a lighter and heated the entire hole where the eyes go, when heating it, I put it to sleep with my fingertips so I could make an expression of evil. I also made some cuts in the part of the nose to be able to make it more embossed and with the same lighter, heat all that part so that the embossing would be more pointed. After this I took a brush and school glue and curetted all the foami, which I then painted with matte black paint.
El foami es muy maleable, especialmente cuando lo podemos someter al calor. Así que para que la máscara no quedara tan uniforme, sino con algunas formas, tomé un encendedor y calente todo el agujero donde van los ojos, al calentarlo le fi dorma con la yema de mis dedos así pude hacerle una expresión de maldad. También hice unos cortes en la parte de la nariz para poder hacerle más relieve y con el mismo encendedor calente toda esa parte para que el relieve quedara más puntiagudo. Después de esto tomé una brocha y pegamento escolar e hice un curetaje a todo el foami, el cual luego pinté con pintura negra en tono mate.
Then I made the shape of the Punisher logo with a pen, and with white acrylic paint I painted the entire area. To cover the foam very well I put 4 layers of paint on the whole, in the area of the nose I also drew the holes of the shell and with the scalpel I made the cuts.
Después hice con un boligrafó la forma del logo de Punisher, y con pintura blanca acrilica fui pintando toda la zona. Para cubrir muy bien el foami puse 4 capas de pintura en todal, en la zona de la naríz tambien dibujé los agujeros de la caravela y con el bisturí hice los cortes.
To finish, I added a microperforated vinyl mesh to the eye holes, as it was green I painted it black, I drew and drew the pattern for both eyes that I later glued with hot silicone on the inside of the mask. Finally I put a league to be able to fix the mask to the face to the extent of my head. And so this Punisher mask was finished.
Para finalizar agregué en los agujeros de los ojos una malla de vinil microperforado, como era de color verde lo pinte de color negro, dibujé y saqué el patrón para ambos ojos que luego pegué con silicón caliente por la parte interna de la máscara. Por último puse una liga para poder fijar la máscara al rostro a la medida de mi cabeza. Y así quedó finalizada esta mascara de Punisher.
FINAL WORK
This is how this Punisher mask was finished, I made it somewhat terrifying because horror costumes are also often made in carnival, and I think it is a good option to use on Halloween, it should be noted that the pattern of this helmet can be adapted to make others, just with a little more creativity it can be given many forms. Punisher is like Batman, but with the difference that he is willing to cross the line to apply justice, which for him is a form of revenge. I hope you liked it, do not forget to comment what you think of this mask model, I say goodbye see you soon and a new opportunity.
Así quedó finalizada esta máscara de Punisher, la hice algo aterradora porque también en carnaval suelen hacerse disfraces de terror, y creo que es una buena opción para usar en Halloween, cabe resaltar que el patrón de este casco se puede adaptar para hacer otros, solo con un poco más de creatividad puede dársele muchas formas. Punisher es como Batman, pero con la diferencia que él si está dispuesto a cruzar la línea para aplicar justicia, la cual para él es una forma de venganza. Espero que les haya gustado, no olviden comentar que les ha parecido este modelo de máscara, me despido hasta pronto y una nueva oportunidad.