🔌✒️Bricolaje, elabora tu propio ordenador de cargadores /Do-it-yourself, make your own charger computer🔌✒️
Hola! Gran familia hive, espero tengan un excelente y provechoso día, en esta ocasión haremos un ordenador de cargadores.
Hello, thank you hive family, I hope you have an excellent and profitable day, this time we will make a charger computer.
Listos??? Hoy vamos a solucionar un problemita que casi todos tenemos con nuestros cargadores, donde el desorden y el maltrato del mismo son los pretagonistas, así que para eso necesitaremos lo siguiente.
Ready? Today we are going to solve a little problem that almost all of us have with our chargers, where disorder and mistreatment are the main characters, so for that we will need the following.
Materiales:
✒️ Un tubo de cartón,(el del papel aluminio).
✒️ La caja del tubo.
✒️ Lápiz.
✒️ Regla.
✒️ Marcador.
✒️ Barra de Silicon.
✒️ Pintura negra,(opcional).
✒️ Pincel.
✒️ Estilete.
✒️ Alambre,(utilice los alambres blancos que traen los sandwiches del supermercado).
Materials:
✒️ A cardboard tube,(the one from the aluminum foil).
✒️ The box of the tube.
✒️ Pencil.
✒️ Ruler.
✒️ Marker.
✒️ Silicon rod.
✒️ Black paint,(optional).
✒️ Brush.
✒️ Stylus.
✒️ Wire,(use the white wires that the sandwiches from the supermarket bring).
🔌 Paso uno:
Con nuestra regla haremos tres divisiones en nuestro tubo, un punto en la medida de 7.5 cm, 15 cm y 22.5 cm.
🔌 Step one:
With our ruler we will make three divisions in our tube, one point in the measure of 7.5 cm, 15 cm and 22.5 cm.
🔌 Paso dos:
Con el Estilete cortaremos en forma de línea en los puntos ya antes marcados, esa línea debe ser un poco gruesa para que entre los cables del cargador y posterior un pequeño cuadrado para que entre la base del mismo, observe.
🔌 Step two:
With the Estilete we will cut in the form of a line at the points already marked before, that line should be a little thick to enter the charger wires and later a small square to enter the base of the charger, note.
🔌Paso tres:
Abriremos la caja del tubo y haremos un cuadrado del tamaño del mismo, súper rápido ya que la caja tiene las medidas del tubo... posterior con el cartón que sobra se hará dos círculos pequeños para tapar el tubo por los lados.
🔌Step three:
We will open the tube box and make a square the size of the tube, super fast since the box has the measurements of the tube... later with the leftover cardboard we will make two small circles to cover the tube on the sides.
🔌Paso cuatro:
Pintaremos todo del color de su preferencia.
🔌Step four:
We will paint everything in the color of your choice.
🔌Paso cinco:
En la parte inferior del cartón que será la base de nuestro tubo, haremos tres orificios (cada uno debajo de la divisiones del tubo), los orificios los hice con del punta del lapiz...posterior pegaremos el tubo al cartón, los círculos pequeños al tubo y nuestra cartón de base a la pared.
Step five:
On the bottom of the cardboard that will be the base of our tube, we will make three holes (each one under the tube divisions), the holes I made them with the tip of the pencil...later we will glue the tube to the cardboard, the small circles to the tube and our base cardboard to the wall.
Nota: Lo plateado que se ve en el cartón es lo que trae la caja del tubo para cortar el papel aluminio, lo usé como adorno.
Note: The silver that you can see in the cardboard is what comes in the box of the tube to cut the aluminum foil, I used it as an ornament.
🔌Paso seis:
Colocaremos nuestros cargadores en el tubo y con los alambres sujetaremos los cables.
🔌Step six:
We will place our chargers in the tube and with the wires we will attach the wires.
Genial!! Ya tenemos súper ordenados nuestros cargadores y la garantía de su duración por su buen cuidado.
Great! We already have our chargers super tidy and the guarantee of its duration due to its good care.