CentOS7 Configuration

Use this guide for setting up Splunk Enterprise on CentOS7. I use the minimal CD for installing CentOS7.

Configure a Hostname

Check the current hostname

# hostnamectl status

Set the hostname

# hostnamectl set-hostname splunk.server.local

Verify the hostname change

# hostnamectl status

Log out and log back in to ensure the hostname is displaying correctly.

Configure NTP

Configure NTP on the server.

# yum install -y ntp ntpdate

Edit the NTP configuration file. Replace the current NTP server addresses with localised Australian servers or the closest NTP server to your host.

# vi /etc/ntp.conf



server 0.au.pool.ntp.org

server 1.au.pool.ntp.org

server 2.au.pool.ntp.org

server 3.au.pool.ntp.org

Turn on the NTP daemon.

# systemctl start ntpd

# systemctl enable ntpd.service

Check the status of the NTP daemon

# systemctl status ntpd

Update the time at the command line if the NTP daemon has yet to be started.

# ntpdate 0.au.pool.ntp.org

Install the Time zone Package

Installing tzdata.noarch through yum will install the latest version.

yum install -y tzdata.noarch

You should also check to make sure that the /etc/localtime link is pointing to a valid time zone. To do that, run the following command:

ls -altrh /etc/localtime

You should get a response similar to this (below), where <ZONE> is your time zone such as:

lrwxrwxrwx. 1 root root 39 Jan 19 15:57 /etc/localtime -> /usr/share/zoneinfo/Australia/Melbourne

If this is not correct, run the following commands as user root:

# source /etc/sysconfig/clock

# mv /etc/localtime /etc/localtime.old

# ln -s /usr/share/zoneinfo/Australia/Melbourne /etc/localtime

# ls -altrh /etc/localtime

**Increase File descriptor limits (FDs) on *nix systems**

Usually, the default file descriptor limit (controlled by the ulimit -n command on a *nix-based OS) is 1024. Your Splunk administrator should determine the correct level. View the current settings with:

# umlimit -a

I have seen the values change with different versions of Splunk so ensure you read Splunks documentation to ensure you have the correct minimum values.

Source: http://docs.splunk.com/Documentation/Splunk/7.1.2/Installation/SystemrequirementsO

n the default version of CentOS 7 I need to change the Open Files and User Processes.

# vi /etc/security/limits.conf



* soft nproc 16000

* hard nproc 16000

* soft nofile 64000

* hard nofile 64000

Update the OS

$ sudo yum update -y

Splunk Installation

Download Splunk

https://www.splunk.com/en_us/download/splunk-enterprise.html#tabs/linux

Create the Splunk User

# groupadd splunk

# useradd -c splunk_software_owner -g splunk -d /home/splunk -m -s /bin/bash splunk

# passwd splunk

# gpasswd -a splunk wheel

Create the Splunk Directory

The default installation directory is /opt/splunk/.Make sure that the user splunk has write and execute permission for the /opt/splunk/ directory. Change the owner and group of /opt/splunk/ to the splunk user and group by issuing the following commands while logged in as root:

# mkdir /opt/splunk

# chown splunk:splunk /opt/splunk

RPM Installation

Logon to the server as the splunk user and add execute the following:Verify the binary's hash.

[splunk@splunk ~]$ sudo yum install -y wget

[splunk@splunk ~]$ openssl dgst -md5 <filename-splunk-downloaded.zip>

or

[splunk@splunk ~]$ openssl dgst -sha512 <filename-splunk-downloaded.zip>

[splunk@splunk ~]$ chmod 744 splunk-*.rpm

[splunk@splunk ~]$ sudo rpm -i splunk-*.rpm

[splunk@splunk bin]$ sudo -H -u splunk /opt/splunk/bin/splunk start --accept-license

Firewall Modifications

splunkd runs a Web server on port 8089 with SSL/HTTPS turned on by default.
It also runs a Web server on port 8000 with SSL/HTTPS turned off by default.

Allow web access on port tcp 8000, syslog on udp 5514

# firewall-cmd --zone=public --permanent --add-port=8000/tcp

# firewall-cmd --zone=public --permanent --add-port=5514/udp

Forward syslog input to high port for non-root, allow port 80 for http

# firewall-cmd --direct --permanent --add-rule ipv4 nat PREROUTING 0 -p udp -m udp --dport 514 -j REDIRECT --to-ports 5514

# firewall-cmd --direct --permanent --add-rule ipv4 nat PREROUTING 0 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 8000

Reload firewall

# firewall-cmd --reload

First Time Login

U/N: admin