Hola amigos, tiempo sin mostrar de mi trabajo en esta comunidad, el día de hoy les traigo un anillo ajustable de patas de mascotas, una pieza encantadora e irresistibles para los amantes de los animales domésticos cómo los perros y los gatos.
Este anillo ajustable fue un pedido que me hicieron la semana pasada, que la verdad lo hice con algo de material que tenía sobrante.
Parte de lo que mostraré en este post son los pasos y una breve descripción, para que se hagan una idea del trabajo que hay detrás de la elaboración de una pieza de joyería.
Materiales que use:
- Lámina de plata de 0.8 mm e hilo de plata de 1.5 mm
- Soldadura de plata.
- Arco de segueta de joyería y sierras de segueta de 1/0
- Dremel con eje flexible, junto a porta lijas y fresa de 0.7 mm para abrir los huecos.
- lijas de granos 220, 360 y 400.
- Motor de banco.
- Mandril de anillos.
- Mopas de algodón para pulir y cera para pulir.
- Pega de Barra.
PROCESO
Rescate una impresión antigua de las patas de mascotas, estas miden un poco menos de 1 cm, debo decir que lamentablemente estas se imprimieron con Tóner y el color se le fue cayendo, como ven en la imagen, las líneas estaban muy difusas, pero decidí avanzar así, les recomiendo que para trabajos de joyería mejor imprimir con tinta; a pesar de todo no podía perder tiempo de buscar el archivo para imprimir, así que asumí el riesgo, por lo que agarre pega de barra y las pegue en un pedazo de lámina de plata de 0.8 mm.
Usando el Dremel y la fresa de 0.7 mm hice los agujeros del interior de las patitas.
Con la segueta y la sierra 1/0 corte primero el interior de las patitas y luego la silueta exterior, en la foto de arriba pueden apreciar como quedan sin haber quitado la impresión.
Después le quité la impresión para poder ver si la pieza hay que repasarla con la segueta o limas para corregir, en este caso corregí muy poco, porque para mi sorpresa había quedado bastante bien.
Un dato necesario es que para quitar la impresión se puede sumergir las piezas en agua o se puede con el soplete quemar.
Volteé la pieza de la pata y le coloqué un cuadro de soldadura, porque allí soldaré el hilo de plata para hacer el anillo, también le puse bórax como fundente.
Alli el hilo de plata y la patita antes de ser soldados... lamentablemente no pude tomar foto de como se suelda, pero si les comento que a la punta del hilo debí aplanarla y lijar un poco para que calzara mejor, soldé un extremo y después con el mandril redondee el aro y soldé la otra pata de mascota.
Este es el resultado, debí después ajustar más con el mandril de anillos, corregir con algunas limas y pasar lijas con ayuda del Dremel en este orden 220,360 y 400, todo antes de pulir.
Para pulir esto si lo hice con mucho cuidado en el motor de banco, usando las mopas de algodón y la cera de pulir. Por último, con una porta lijas envuelto en algodón y el Dremel, pulí los espacios interiores del anillo, después limpié con agua y jabón desengrasante.
Este fue el resultado final.
Bueno espero les haya gustado este anillo,a la chica que se lo hice le encantó.
Si quieres conocer más de mi trabajo de joyería me pueden seguir en:
https://instagram.com/m16ueljoyas
.....
ENGLISH / Google translator
.....
Hello friends, time without showing my work in this community, today I bring you an adjustable ring with pet paws, a charming and irresistible piece for lovers of pets like dogs and cats.
This adjustable ring was an order that they made me last week, which I actually did with some material that I had left over.
Part of what I will show in this post are the steps and a brief description, so that you get an idea of the work that goes into making a piece of jewelry.
Materials I used:
- 0.8 mm silver foil and 1.5 mm silver wire
- Silver solder.
- 1/0 Jeweler's Hacksaw Bow and Hacksaws
- Dremel with flexible shaft, along with a sandpaper holder and a 0.7 mm cutter to open the holes.
- 220, 360 and 400 grit sandpaper.
- Bench engine.
- Ring mandrel.
- Cotton mops for polishing and polishing wax.
- Bar Paste.
PROCESS
I rescued an old print of pet paws, they measure a little less than 1 cm, I must say that unfortunately they were printed with Toner and the color faded, as you can see in the image, the lines were very blurred, but I decided To advance like this, I recommend that for jewelry works it is better to print with ink; Despite everything, I couldn't waste time looking for the file to print, so I took the risk, so I took glue sticks and glued them to a piece of 0.8 mm silver foil.
Using the Dremel and the 0.7mm bur, I made the holes on the inside of the legs.
With the hacksaw and the 1/0 saw, first cut the inside of the legs and then the outer silhouette, in the photo above you can see how they look without having removed the print.
Later I removed the impression to be able to see if the piece should be revised with a saw blade or files to correct it, in this case I corrected very little, because to my surprise it had turned out quite well.
A necessary piece of information is that to remove the impression, the pieces can be submerged in water or burned with a blowtorch.
I turned the leg piece over and put a soldering box on it, because there I will solder the silver wire to make the ring, I also put borax on it as a flux.
There the silver thread and the leg before being soldered... unfortunately I couldn't take a photo of how it is soldered, but I do tell you that I had to flatten it at the end of the thread and sand it down a bit to make it fit better, I soldered one end and then with the mandrel I rounded the ring and welded the other pet leg.
This is the result, I had to adjust further with the ring mandrel, correct with some files and sandpaper with the help of the Dremel in this order 220, 360 and 400, all before polishing.
To polish this I did very carefully on the bench motor, using the cotton pads and polishing wax. Lastly, with a sandpaper holder wrapped in cotton and the Dremel, I sanded down the inner spaces of the ring, then cleaned with degreasing soap and water.
This was the final result.
Well I hope you liked this ring, the girl I made it for her loved it.
If you want to know more about my jewelry work you can follow me on: