Hello chicos, qué tal su día de ayer? Yo estuve bastante ocupadita y no pude pasar por el blog, pero ya hoy estamos de vuelta para compartir con ustedes el paso a paso de unos pendientes que realicé para que hicieran juego con el brazalete 3 en 1 que compartí con ustedes hace poco y como me gustó tato decidí hacer unos zarcillos que hicieran juego con él.
Hi everyone, how was your day yesterday? I was quite busy and couldn’t pop by the blog, but we’re back today to share with you a step-by-step guide to some earrings I made to match the 3-in-1 bracelet that I shared with you recently, and as I liked it so much, I decided to make some earrings to go with it.

Para su elaboración, al igual que con la pulsera, estuve utilizando mostacillas blancas nacradas o tornasol y balínes pequeños dorado, ya que por supuesto necesitábamos que hicieran juego con el brazalete. Y en esta oportunidad para estos pendientes decidí utilizar pines en lugar de un gancho ya que la verdad el pin me gusta mucho más. Y ahora sí vamos con el paso a paso y los materiales.
To make them, just as with the bracelet, I used white pearlescent or iridescent beads and small gold beads, as we obviously needed them to match the bracelet. And this time, for these earrings, I decided to use studs instead of hooks, as I actually much prefer the stud style. And now let’s get on with the step-by-step guide and the materials.

Materiales
Alfileres de ojo
Mostacillas blancas tornasol
Balines pequeños
Pines para zarcillos
Tenaza
Pinza plana
Pinza redonda
Materials
Eye pins
Iridescent white beads
Small seed beads
Earring posts
Pliers
Flat-nose pliers
Round-nose pliers
Paso a paso/Step by step
Como siempre les traigo un trabajo muy fácil de hacer, pero súper lindo, muy femenino y delicado, y para su elaboración, vamos a necesitar 3 piezas, y se trata de dos colgantes elaborados con mostacillas y balines en 2 tamaños diferentes y un balín en litario, y para comenzar con el primero vamos a utilizar un alfiler de ojo y mostacillas blancas y doradas que vamos a ir intercalando de la siguiente manera: 2 mostacillas y un balín dorado hasta tener 4 bloques de 2 de mostacillas blancas.
Al finalizar, cortamos el excedente y en este caso como no vamos a conectar ninguna otra pieza. en ese extremo lo cortaremos mucho más pequeño que de costumbre. ¿y cerramos con ayuda de la pinza redonda y la pinza plana y les va a quedar tal cual como lo ven en la última imagen.
As always, I’ve got a project for you that’s very easy to make, but absolutely lovely, very feminine and delicate, To make it, we’ll need three pieces: two pendants made from seed beads and round beads in two different sizes. To start with the first one, we’ll use an eye pin and white and gold seed beads, which we’ll alternate as follows: two seed beads and one gold round bead, until we have four blocks of two white seed beads.
When finished, cut off the excess; in this case, as we won’t be connecting any other pieces, we’ll cut that end much shorter than usual. Then close it using the round-nose pliers and flat-nose pliers, and it will look exactly as you see in the last image.


El siguiente paso es crear la segunda pieza de nuestro pendiente y es básicamente lo mismo solo que este será un poco más corto, así que utilizaremos solo dos bloques de mostacillas blancas, intercalando balines, y para cerrar hacemos lo mismo que en el paso anterior.
The next step is to make the second part of our earring; it’s basically the same, except this one will be a little shorter, so we’ll use just two strands of white beads, interspersed with small beads, and to fasten it, we’ll do the same as in the previous step.

Seguidamente elaboraremos la última pieza, la cual consiste en un balín en solitario, y para ello utilizaremos un alfiler de ojo, por el que hacemos pasar nuestro balín, y cortamos el excedente, dejando poco menos de 1 centímetro de largo, ya que en esta oportunidad sí vamos a crear un arito pues necesitamos conectar piezas de ambos extremos.
Para ello, lo que hacemos es colocar la pinza redonda en el extremo del alfiler de ojo y giramos sobre sí misma hacia adentro creando de esta forma nuestro aro.
Next, we’ll make the final piece, which consists of a single bead. To do this, we’ll use an eye pin, thread the bead onto it, and cut off the excess, leaving just under 1 centimetre in length, as this time we are going to create a loop and need to connect the pieces at both ends.
To do this, we place the round crimp bead on the end of the eye pin and twist it inwards, thus creating our ring.

Una vez tenemos listas todas las piezas el siguiente paso es comenzar con el armado de nuestros pendientes y lo que haremos es tomar la pieza con el balín en solitario y conectar en primer lugar uno de sus extremos a nuestro pin y para esto lo abrimos un poco con la pinza redonda hacemos pasar el pin y finalmente cerramos con la pinza plana, asegurándonos de sellar muy bien.
En el otro extremo vamos a hacer pasar las piezas que hicimos anteriormente, una larga y una corta para cada pendiente, y lo haremos de la misma forma que en el paso anterior y de esta manera tenemos listos estos hermosos pendientes que hacen un match perfecto con el brazalete tres en uno que les compartí hace poco.
Once all the pieces are ready, the next step is to start assembling our earrings. We’ll take the piece with the single bead and first attach one end to our pin. To do this, we open it slightly with the round-nose pliers, thread the pin through, and finally close it with the flat-nose pliers, making sure it’s securely sealed.
At the other end, we’ll thread through the pieces we made earlier—one long and one short for each earring—and we’ll do this in the same way as in the previous step. And just like that, we’ve finished these beautiful earrings, which are a perfect match for the three-in-one bracelet I shared with you recently.



Como pueden ver es un proceso bastante sencillo de hacer, cero complicado y que luce absolutamente hermoso, y la verdad es que a mí me encantó, y espero que ustedes también y sobre todo que se animen a elaborarlos en casa.
As you can see, it’s a really simple process – not at all complicated – and it looks absolutely stunning. To be honest, I loved it, and I hope you do too, and above all that you’ll give it a go at home.
📷Photography by|Fotografía por:,🔅 Cover created in/Portada creada en Canva, Separator and banner/separador y banner, 🇺🇸Translated with www.DeepL.com/Translator (free version)