Estoy probando un nuevo estilo de anillo ajustable con figuras, así que por allí tenía ya una silueta de mariposa cortada desde hace un tiempo y me dispuse a aprovecharla, pero antes te cuento sobre que herramientas y materiales use:
Silueta de mariposa previamente cortada en lámina de bronce de 0.5 mm.
Soldadura Harris y soplete
hilo de cobre de 1 mm.
Mandril para anillos
Pinzas de joyería
Limas y lija 3M 220, 360 y 400
Dremel
Motor de Banco, mopa y cera de pulir
PROCESO
Esta es la mariposa que conseguí previamente cortada, el espesor de la lámina es 0.5 mm que en teoría es lo suficiente delgada para doblar con facilidad y lo suficientemente dura para que luego no se deforme.
Pasamos luego a aplicar la soldadura con el soplete y queda algo así, ya antes lo había doblado un poco la silueta de la mariposa con la pinza.
Aquí puse el alambre de cobre y soldé. Me apoyé usando una de las pinzas especiales para soldadura.
Utilizando el mandril de anillos hice el aro y con ayuda de la pinza redonda fui dando forma curvas para simular el trayecto del vuelo de la mariposa.
Corregí algunos detalles con usando lija
Como ven en la imagen al anillo le hacía falta una lijada, así que le pase las lijas 220, 360 y 400, para que estuvieran listas para pulir.
Después, antes de terminar, pase a pulir con el motor de banco, empleando una mopa de tela de algodón dura y otra blanda, empleando una cera espacial para dar brillo, para mejorar algunos detalles, hice lo mismo usando el Dremel, al ser más pequeño evitaría accidentes y podría enfocarme mejor en ciertos sitios.
Limpie con agua y jabón desengrasante el exceso y residuos de cera para mandar a bañar en plata.
Este es el resultado final.
Animacion hecha con Capcut
Edición de foto del anillo hecha con Picsart, para publicar en mis redes sociales.
Hasta aquí mi post del proceso de creación de este anillo de mariposa, espero les allá gustado, próximamente publicaré uno parecido con una flor.
Si gustan pueden ver más de mi trabajo de joyería y seguirme por:
https://Instagram.com/m16ueljoyas
+++++++
+++++++
+++++++
ENGLISH
Google Translator
I'm trying a new style of adjustable ring with figures, so I already had a butterfly silhouette cut out there for a while and I decided to take advantage of it, but first I'll tell you about what tools and materials I used:
Butterfly silhouette previously cut in 0.5 mm bronze sheet.
Harris welding and torch
1 mm copper wire.
Ring mandrel
Jewelry tweezers
Files and sandpaper 3M 220, 360 and 400
Dremel
Bench motor, mop and polishing wax
PROCESS
This is the butterfly that I got previously cut, the thickness of the sheet is 0.5 mm, which in theory is thin enough to bend easily and hard enough so that it does not deform later.
We then proceed to apply the solder with the blowtorch and it looks something like this, the silhouette of the butterfly had already bent it a little with the tweezers.
Here I put the copper wire and soldered. I supported myself using one of the special welding pliers.
Using the ring mandrel I made the ring and with the help of the round tweezers I shaped curves to simulate the path of the butterfly's flight.
I corrected some details using sandpaper
As you can see in the image, the ring needed sanding, so I used sandpaper 220, 360 and 400, so that they were ready to polish.
Then, before finishing, I went on to polish with the bench motor, using a hard and soft cotton cloth mop, using a space wax to give shine, to improve some details, I did the same using the Dremel, as it was more small would avoid accidents and I could focus better on certain places.
Clean the excess and wax residue with water and degreasing soap to send it to silver plating.
This is the final result.
Animation made with Capcut
Photo editing of the ring made with Picsart, to publish on my social networks.
That's it for my post on the process of creating this butterfly ring, I hope you like it, soon I will publish one similar to a flower.
If you like you can see more of my jewelry work and follow me on:
https://Instagram.com/m16ueljoyas
+++++++
+++++++
+++++++