HOW TO PUT A HAND IN THE PIPE
My arm does not fit into this tube, especially because it is not open at the back. So I took the two parts separately during a single exposure. I first aligned the camera with the tube and then marked the tube on the camera display. Then I set up a second tripod and attached a template with a round hole in front of the lens. I then aligned this hole exactly with the mark on the display. I placed my hand behind the template, blew some mist behind it and then illuminated my hand. Then I switched the camera to the first tripod and lit the tube and the room with a warm white high CRI torch. You can see the second attempt here, I didn't like the position of my hand so much in the first attempt.
Mein Arm passt nicht in dieses Rohr, vor Allem nicht, weil das hinten nicht offen ist. Also habe ich während einer einzelnen Belichtung die beiden Teile separat aufgenommen. Ich habe zuerst die Kamera auf das Rohr ausgerichtet und dann auf dem Display der Kamera das Rohr markiert. Dann habe ich ein zweites Stativ aufgestellt und vor dem Objektiv eine Schablone mit einem runden Loch befestigt. Dieses Loch habe ich dann genau auf die Markierung auf dem Display ausherichtet. Ich habe meine Hand hinter der Schablone platziert, etwas Nebel dahinter geblasen und dann meine Hand beleuchtet. Danach habe ich die Kamera auf das erste Stativ gewechselt und das Rohr und den Raum mit einer warmweißen High CRI Taschenlampe beleuchtet. Ihr seht hier den zweiten Versuch, beim ersten Versuch gefiel mir die Position meiner Hand nicht so gut.
📷 Nikon D750 - Nikkor 17-35/2,8 f11 - ISO 100 - 221 seconds
The way of working in the next picture was basically the same. I created the light figure in the tube by camera rotation, this had a diameter of about 2 metres. I had mounted a rotating light source on a tripod and rotated the camera 30° around the optical axis after each rotation. I needed a total of 4 attempts for this shot because the size of the rotation did not fit. In the first two attempts the light figure was too large, in the third attempt too small and in the fourth attempt it fitted.
Die Arbeitsweise im nächsten Bild war im Prinzip gleich. Die Lichtfigur im Rohr habe ich durch Camera Rotation erstellt, diese hatte einen Durchmesser von ungefähr 2 Meter. Ich hatte eine rotierende Lichtquelle auf einem Stativ befestigt und nach jeder Umdrehung die Kamera 30° um die optische Achse gedreht. Bei dieser Aufnahme habe ich insgesamt 4 Versuche gebraucht weil die Größe der Rotation nicht gepasst hat. Bei den ersten beiden Versuchen war die Lichtfigur zu groß, beim dritten Versuch zu klein und beim vierten Versuch hat das dann gepasst.
📷 Nikon D750 - Nikkor 17-35/2,8 f8 - ISO 100 - 217 seconds
For the last picture of this night I used the undefined converted Nikon D300. I have removed the hot mirror filter. So the camera now captures the full spectrum of light. I screwed a 920 nm IR filter onto the Nikkor 17-35. The result is always a pure black and white photo. I then illuminated the room with an infrared torch. But that was anything but easy. Infrared radiation is heat radiation. The cold pipe in the cold basement did not really want to reflect the infrared radiation. I had to illuminate the pipe from a very short distance for about 60 seconds so that it could be seen in the picture. Then I removed the IR filter and illuminated the stencil with the Biohazard logo. To do this, I had aligned the stencil exactly as in the first picture.
Photographing black and white and colour in a single shot without subsequent processing on the computer is something very special. Besides the artistic aspect, I am also interested in the physical aspects. In any case, it is always a special challenge because you cannot see infrared or ultraviolet light. So you work completely blind. So that I can orientate myself at all, I set up a small lamp with green light. The green light is not picked up by the camera with the IR filter mounted.
Für das letzte Bild dieser Nacht habe ich die undefiniert umgebaute Nikon D300 benutzt. Ich habe das Hot Mirror Filter entfernt. Somit nimmt die Kamera jetzt das volle Lichtspektrum auf. Ich habe einen 920 nm IR Filter an das Nikkor 17-35 geschraubt. Das Ergebnis ist damit immer ein reines schwarzweiß Foto. Ich habe dann den Raum mit einer Infrarot Taschenlampe beleuchtet. Das war allerdings alles andere als einfach. Infrarotstrahlung ist Wärmestrahlung. Das kalte Rohr im kalten Keller wollte nicht so recht die Infrarotstrahlung reflektieren. Ich habe das Rohr aus sehr kurzer Entfernung ca. 60 Sekunden anleuchten müssen damit es im Bild zu sehen ist. Danach habe ich das IR Filter entfernt und die Schablone mit dem Biohazard Logo beleuchtet. Dazu hatte ich die Schabone wieder vorher genau ausgerichtet wie beim ersten Bild.
Schwarzweiß und Farbe in einer einzelnen Aufnahme ohne nachträgliche Bearbeitung am Computer zu fotografieren ist schon etwas sehr spezielles. Neben dem künstlerischen Aspekt interessieren mich auch die physikalischen Aspekte. Auf jeden Fall ist das immer eine besondere Herausforderung weil man infrarotes oder auch ultravioletes Licht nicht sehen kann. Man arbeitet also komplett blind. Damit ich mich überhaupt orientieren kann stelle ich eine kleine Lampe mit grünem Licht auf. Das grüne Licht nimmt die Kamera mit dem montierten IR Filter nicht auf.
📷 Nikon D300 (full spectrum converted) - Nikkor 17-35/2,8 f11 - ISO 200 - 275 seconds
WHAT IS LIGHT PAINTING?
LICHTKUNSTFOTO
If you like my art visit www.lichtkunstfoto.de for more Light Art Photography and informations about Light Painting. Join me on Flickr Twitter
For more great Light Art Photography, Light Painting and inspiration check these light painters:
WE ARE LIGHT PAINTERS
To help and support the LightPainters community here on Hive I would appreciate your delegation of HivePower. Any amount is appreciated. It does not require much to get started, we are happy for any gesture.
How to delegate?
Delegate 50HivePower, [50HP]
Delegate 250HivePower, [250HP]
Delegate 500HivePower, [500HP]
Delegate 1000HivePower, [1000HP]
All the Hive Power will help to upvote the artist's contribution as part of the LightPainters community.